MIB File
PMP 320 AP (Advanced)

Module Information:
File: DAN-ADV-MIB-ADMIN
Description: PMP 320 AP Adv MIB tree
Organization: Cambium Networks
Version: Software Release e2.3
Contact Info: PMP Technical Support
email : support@cambiumnetworks.com

Notification Summary
None Defined
Object Summary
danConvergenceMode Object ID: 1.3.1.4.1.32584.1.1.1.9
The system convergence modes (types) are:
1. L3
2. L2
3. Undefined( not allowed to set this mode)
Default is L3
danIsolationMode Object ID: 1.3.1.4.1.32584.1.1.1.10
UL air traffic SMs isolation configuration:
0 - No isolation
1 - isolate and drop
2 - isolate and forward to GMAC interface

Default value: 0
danOperationMode Object ID: 1.3.1.4.1.32584.1.1.1.1
Select system operation mode to one of the followings:

- StandAloneMode - Mode when SF provisioning and CPE authontication are manually configure via the AP MIB.
- IntegratedMode - Mode when SF provisioning and CPE authontication are provided by a connected AAA.
- spectrumAnalyzerMode - Special test mode where the AP is used as a spectrum analyzer tool

Default is Integrated Mode
danSaIntervalId Object ID: 1.3.1.4.1.32584.1.2.10.3
Specify the scanning interval as one of the following values:
3.5MHz, 5MHz, 7MHz, 10MHz. The range between danSpaRngFreqMin and
danSpaRngFreqMax is divided into bands and measurement is made at each one.
The default is set to current RF frequency bandwidth
danSaRngFreqMax Object ID: 1.3.1.4.1.32584.1.2.10.2
Specify the maximum frequency in KHz for the scanning range The default value is
automatically set based on RF type.
This parameter is not persistent

danSaRngFreqMin Object ID: 1.3.1.4.1.32584.1.2.10.1
Specify the minimum frequency in KHz for the scanning range The default value is
automatically set based on RF type.
This parameter is not persistent

danSaScanCmd Object ID: 1.3.1.4.1.32584.1.2.10.6
Command to start/stop scanning

danSaScanDuration Object ID: 1.3.1.4.1.32584.1.2.10.5
Defines time interval during which a single band is scanned. Range is 10-60000 milisec.
Default is 1000 milisec
danSaScanMode Object ID: 1.3.1.4.1.32584.1.2.10.4
Selects the scan mode – continues or one-time.
In one-time mode the scanning process will be stopped after the end of range
(danSpaRngFreqMax, see above) reached. In continues mode the scanning for the
same range and intervals will be repeated from the beginning multiple times until it
is stopped by danSaScanCmd Stop.
The default is one-time
danSaScanResCurrPwr Object ID: 1.3.1.4.1.32584.1.2.10.8.1.4
Keeps the current value in dBm measured for the given scanning interval
danSaScanResIntervalCentralFreq Object ID: 1.3.1.4.1.32584.1.2.10.8.1.6
Textual description of the scanning interval central frequency channel in human readable format E.g. '3.60 GHz'
danSaScanResIntervalDsc Object ID: 1.3.1.4.1.32584.1.2.10.8.1.2
Textual description of the scanning interval in human readable format E.g. '3.60 – 3.61 GHz'
danSaScanResIntervalId Object ID: 1.3.1.4.1.32584.1.2.10.8.1.1
Indicate the scanning interval Id
danSaScanResMeanPwr Object ID: 1.3.1.4.1.32584.1.2.10.8.1.5
Keeps the mean value in dBm measured for the given scanning interval
danSaScanResPeakPwr Object ID: 1.3.1.4.1.32584.1.2.10.8.1.3
Keeps the peak value in dBm measured for the given scanning interval
danSaScanState Object ID: 1.3.1.4.1.32584.1.2.10.7
Bool. Current scanning state:
FALSE: Not active
TRUE: in process


danSpaScanResEntry Object ID: 1.3.1.4.1.32584.1.2.10.8.1
Each entry represent result for measured frequency slice
danSpaScanResTable Object ID: 1.3.1.4.1.32584.1.2.10.8
Table contains scanning result
danUnlicensedDetHistAvg Object ID: 1.3.1.4.1.32584.1.8.10.2.1.6
Level of average RSSI (dBM) calculated at the time of interference event.
danUnlicensedDetHistBw Object ID: 1.3.1.4.1.32584.1.8.10.2.1.4
RF Bandwidth AP was operating in at the time of the interference event
danUnlicensedDetHistDatetime Object ID: 1.3.1.4.1.32584.1.8.10.2.1.2
Date and time
danUnlicensedDetHistEntry Object ID: 1.3.1.4.1.32584.1.8.10.2.1
Description.
danUnlicensedDetHistId Object ID: 1.3.1.4.1.32584.1.8.10.2.1.1
Index of table
danUnlicensedDetHistPeak Object ID: 1.3.1.4.1.32584.1.8.10.2.1.7
Level of peak RSSI (dBM) calculated at the time of interference event.
danUnlicensedDetHistRf Object ID: 1.3.1.4.1.32584.1.8.10.2.1.3
Center frequency AP was operating in at the time of the interference event
danUnlicensedDetHistTable Object ID: 1.3.1.4.1.32584.1.8.10.2
The table contains an entry for each learned MAC address (Ethernet station)
danUnlicensedDetHistTimeInterval Object ID: 1.3.1.4.1.32584.1.8.10.2.1.5
Time interval AP was using at the time of the interference event
danUnlicensedModeEnable Object ID: 1.3.1.4.1.32584.1.25.1
Enable/disable unlicensed mode. Default is disabled.
danUnlicensedSelFreqListCenterFr Object ID: 1.3.1.4.1.32584.1.25.2.1.2
Center Frequency
danUnlicensedSelFreqListEntry Object ID: 1.3.1.4.1.32584.1.25.2.1
A table that holds up to 10 channels to scan. A channel to scan is defined by a center frequency and a bandwidth.The list actually specifies the center frequency of the channel (in units of KHz). The channel bandwidth is derived from the AP current configuration of RF bandwidth (3.5MHz, 5MHz, 7MHz or 10MHz). The frequncies can be selected with offsets of 500 KHz. List is empty by default.
Note that each channel must be in the range of the unlicensed 3.65-3.70 GHz band, otherwise the channel is skipped (e.g., a center frequency that yield a valid channel for bandwidth of 5MHz might yield an invalid channel for bandwidth of 10MHz).
danUnlicensedSelFreqListId Object ID: 1.3.1.4.1.32584.1.25.2.1.1
Index of table
danUnlicensedSelFreqListTable Object ID: 1.3.1.4.1.32584.1.25.2
A table that holds up to 10 channels to scan. A channel to scan is defined by a center frequency and a bandwidth.The list actually specifies the center frequency of the channel (in units of KHz). The channel bandwidth is derived from the AP current configuration of RF bandwidth (3.5MHz, 5MHz, 7MHz or 10MHz). The frequncies can be selected with offsets of 500 KHz. List is empty by default.
Note that each channel must be in the range of the unlicensed 3.65-3.70 GHz band, otherwise the channel is skipped (e.g., a center frequency that yield a valid channel for bandwidth of 5MHz might yield an invalid channel for bandwidth of 10MHz).
danUnlicensedSelectedChannel Object ID: 1.3.1.4.1.32584.1.8.10.1
Textual description of the RF channel selected for operational mode, in human readable format E.g. “3.680 GHz”. As long as no channel selected, returns zero value.
 

Object Details

danConvergenceMode

Object ID: 1.3.1.4.1.32584.1.1.1.9
Syntax: INTEGER
Constraints:
0: l3
1: l2
2: undefined

Access: read-write
Status: current

The system convergence modes (types) are:
1. L3
2. L2
3. Undefined( not allowed to set this mode)
Default is L3

danIsolationMode

Object ID: 1.3.1.4.1.32584.1.1.1.10
Syntax: INTEGER
Constraints:
0: danNoIsolation
1: danIsolateAndDrop
2: danIsolateAndFrwrd

Access: read-write
Status: current

UL air traffic SMs isolation configuration:
0 - No isolation
1 - isolate and drop
2 - isolate and forward to GMAC interface

Default value: 0

danOperationMode

Object ID: 1.3.1.4.1.32584.1.1.1.1
Syntax: INTEGER
Constraints:
0: standAloneMode
1: integratedMode
2: spectrumAnalyzerMode

Access: read-write
Status: current

Select system operation mode to one of the followings:

- StandAloneMode - Mode when SF provisioning and CPE authontication are manually configure via the AP MIB.
- IntegratedMode - Mode when SF provisioning and CPE authontication are provided by a connected AAA.
- spectrumAnalyzerMode - Special test mode where the AP is used as a spectrum analyzer tool

Default is Integrated Mode

danSaIntervalId

Object ID: 1.3.1.4.1.32584.1.2.10.3
Syntax: Gauge
Constraints: 0..4294967295
Access: read-only
Status: current

Specify the scanning interval as one of the following values:
3.5MHz, 5MHz, 7MHz, 10MHz. The range between danSpaRngFreqMin and
danSpaRngFreqMax is divided into bands and measurement is made at each one.
The default is set to current RF frequency bandwidth

danSaRngFreqMax

Object ID: 1.3.1.4.1.32584.1.2.10.2
Syntax: Gauge
Constraints: 0..4294967295
Access: read-write
Status: current

Specify the maximum frequency in KHz for the scanning range The default value is
automatically set based on RF type.
This parameter is not persistent

danSaRngFreqMin

Object ID: 1.3.1.4.1.32584.1.2.10.1
Syntax: Gauge
Constraints: 0..4294967295
Access: read-write
Status: current

Specify the minimum frequency in KHz for the scanning range The default value is
automatically set based on RF type.
This parameter is not persistent

danSaScanCmd

Object ID: 1.3.1.4.1.32584.1.2.10.6
Syntax: INTEGER
Constraints:
0: scanNoAction
1: scanStart
2: scanStop

Access: read-write
Status: current

Command to start/stop scanning

danSaScanDuration

Object ID: 1.3.1.4.1.32584.1.2.10.5
Syntax: Gauge
Constraints: 0..4294967295
Access: read-write
Status: current

Defines time interval during which a single band is scanned. Range is 10-60000 milisec.
Default is 1000 milisec

danSaScanMode

Object ID: 1.3.1.4.1.32584.1.2.10.4
Syntax: INTEGER
Constraints:
1: scnModeOneTime
2: scnModeCont

Access: read-write
Status: current

Selects the scan mode – continues or one-time.
In one-time mode the scanning process will be stopped after the end of range
(danSpaRngFreqMax, see above) reached. In continues mode the scanning for the
same range and intervals will be repeated from the beginning multiple times until it
is stopped by danSaScanCmd Stop.
The default is one-time

danSaScanResCurrPwr

Object ID: 1.3.1.4.1.32584.1.2.10.8.1.4
Syntax: OCTET STRING
Access: read-only
Status: current

Keeps the current value in dBm measured for the given scanning interval

danSaScanResIntervalCentralFreq

Object ID: 1.3.1.4.1.32584.1.2.10.8.1.6
Syntax: OCTET STRING
Access: read-only
Status: current

Textual description of the scanning interval central frequency channel in human readable format E.g. '3.60 GHz'

danSaScanResIntervalDsc

Object ID: 1.3.1.4.1.32584.1.2.10.8.1.2
Syntax: OCTET STRING
Access: read-only
Status: current

Textual description of the scanning interval in human readable format E.g. '3.60 – 3.61 GHz'

danSaScanResIntervalId

Object ID: 1.3.1.4.1.32584.1.2.10.8.1.1
Syntax: INTEGER
Constraints: 1..500
Access: read-only
Status: current

Indicate the scanning interval Id

danSaScanResMeanPwr

Object ID: 1.3.1.4.1.32584.1.2.10.8.1.5
Syntax: OCTET STRING
Access: read-only
Status: current

Keeps the mean value in dBm measured for the given scanning interval

danSaScanResPeakPwr

Object ID: 1.3.1.4.1.32584.1.2.10.8.1.3
Syntax: OCTET STRING
Access: read-only
Status: current

Keeps the peak value in dBm measured for the given scanning interval

danSaScanState

Object ID: 1.3.1.4.1.32584.1.2.10.7
Syntax: INTEGER
Constraints:
0: false
1: true

Access: read-only
Status: current

Bool. Current scanning state:
FALSE: Not active
TRUE: in process


danSpaScanResEntry

Object ID: 1.3.1.4.1.32584.1.2.10.8.1
Syntax: Sequence (Structure)
danSaScanResIntervalId
danSaScanResIntervalDsc
danSaScanResPeakPwr
danSaScanResCurrPwr
danSaScanResMeanPwr
danSaScanResIntervalCentralFreq

Access: not-accessible
Status: current

Each entry represent result for measured frequency slice

danSpaScanResTable

Object ID: 1.3.1.4.1.32584.1.2.10.8
Syntax: Sequence of Type (Array)
DanSpaScanResEntry

Access: not-accessible
Status: current

Table contains scanning result

danUnlicensedDetHistAvg

Object ID: 1.3.1.4.1.32584.1.8.10.2.1.6
Syntax: OCTET STRING
Access: read-only
Status: current

Level of average RSSI (dBM) calculated at the time of interference event.

danUnlicensedDetHistBw

Object ID: 1.3.1.4.1.32584.1.8.10.2.1.4
Syntax: OCTET STRING
Access: read-only
Status: current

RF Bandwidth AP was operating in at the time of the interference event

danUnlicensedDetHistDatetime

Object ID: 1.3.1.4.1.32584.1.8.10.2.1.2
Syntax: OCTET STRING
Access: read-only
Status: current

Date and time

danUnlicensedDetHistEntry

Object ID: 1.3.1.4.1.32584.1.8.10.2.1
Syntax: Sequence (Structure)
danUnlicensedDetHistId
danUnlicensedDetHistDatetime
danUnlicensedDetHistRf
danUnlicensedDetHistBw
danUnlicensedDetHistTimeInterval
danUnlicensedDetHistAvg
danUnlicensedDetHistPeak

Access: not-accessible
Status: current

Description.

danUnlicensedDetHistId

Object ID: 1.3.1.4.1.32584.1.8.10.2.1.1
Syntax: INTEGER
Constraints: 1..10
Access: read-only
Status: current

Index of table

danUnlicensedDetHistPeak

Object ID: 1.3.1.4.1.32584.1.8.10.2.1.7
Syntax: OCTET STRING
Access: read-only
Status: current

Level of peak RSSI (dBM) calculated at the time of interference event.

danUnlicensedDetHistRf

Object ID: 1.3.1.4.1.32584.1.8.10.2.1.3
Syntax: OCTET STRING
Access: read-only
Status: current

Center frequency AP was operating in at the time of the interference event

danUnlicensedDetHistTable

Object ID: 1.3.1.4.1.32584.1.8.10.2
Syntax: Sequence of Type (Array)
DanUnlicensedDetHistEntry

Access: not-accessible
Status: current

The table contains an entry for each learned MAC address (Ethernet station)

danUnlicensedDetHistTimeInterval

Object ID: 1.3.1.4.1.32584.1.8.10.2.1.5
Syntax: INTEGER
Constraints: -2147483648..2147483647
Access: read-only
Status: current

Time interval AP was using at the time of the interference event

danUnlicensedModeEnable

Object ID: 1.3.1.4.1.32584.1.25.1
Syntax: INTEGER
Constraints:
0: disable
1: enable

Access: read-write
Status: current

Enable/disable unlicensed mode. Default is disabled.

danUnlicensedSelFreqListCenterFr

Object ID: 1.3.1.4.1.32584.1.25.2.1.2
Syntax: Gauge
Constraints: 0..4294967295
Access: read-write
Status: current

Center Frequency

danUnlicensedSelFreqListEntry

Object ID: 1.3.1.4.1.32584.1.25.2.1
Syntax: Sequence (Structure)
danUnlicensedSelFreqListId
danUnlicensedSelFreqListCenterFr

Access: not-accessible
Status: current

A table that holds up to 10 channels to scan. A channel to scan is defined by a center frequency and a bandwidth.The list actually specifies the center frequency of the channel (in units of KHz). The channel bandwidth is derived from the AP current configuration of RF bandwidth (3.5MHz, 5MHz, 7MHz or 10MHz). The frequncies can be selected with offsets of 500 KHz. List is empty by default.
Note that each channel must be in the range of the unlicensed 3.65-3.70 GHz band, otherwise the channel is skipped (e.g., a center frequency that yield a valid channel for bandwidth of 5MHz might yield an invalid channel for bandwidth of 10MHz).

danUnlicensedSelFreqListId

Object ID: 1.3.1.4.1.32584.1.25.2.1.1
Syntax: INTEGER
Constraints: 1..10
Access: read-only
Status: current

Index of table

danUnlicensedSelFreqListTable

Object ID: 1.3.1.4.1.32584.1.25.2
Syntax: Sequence of Type (Array)
DanUnlicensedSelFreqListEntry

Access: not-accessible
Status: current

A table that holds up to 10 channels to scan. A channel to scan is defined by a center frequency and a bandwidth.The list actually specifies the center frequency of the channel (in units of KHz). The channel bandwidth is derived from the AP current configuration of RF bandwidth (3.5MHz, 5MHz, 7MHz or 10MHz). The frequncies can be selected with offsets of 500 KHz. List is empty by default.
Note that each channel must be in the range of the unlicensed 3.65-3.70 GHz band, otherwise the channel is skipped (e.g., a center frequency that yield a valid channel for bandwidth of 5MHz might yield an invalid channel for bandwidth of 10MHz).

danUnlicensedSelectedChannel

Object ID: 1.3.1.4.1.32584.1.8.10.1
Syntax: OCTET STRING
Access: read-only
Status: current

Textual description of the RF channel selected for operational mode, in human readable format E.g. “3.680 GHz”. As long as no channel selected, returns zero value.