| Notification Summary | |
| regulatoryApCheckInvalidChBwFailed |
Object ID: 1.3.6.1.4.1.161.19.3.1.5.4.3
Regulatory Check failed due to an invalid channel bandwidth for the configured region. regulatoryStatus - Text description for the failure. physAddress - the MAC address of the unit. |
| regulatoryApCheckInvalidChanFailed |
Object ID: 1.3.6.1.4.1.161.19.3.1.5.4.1
Regulatory Check failed for the unit due to a invalid channel for the configured region. regulatoryStatus - Text description for the failure. physAddress - the MAC address of the unit. |
| regulatoryCheckFailedNoRegionAp |
Object ID: 1.3.6.1.4.1.161.19.3.1.5.4.2
Regulatory Check failed because a valid region has not be configured. physAddress - the MAC address of the unit. |
| rfLinkOverloadCondition |
Object ID: 1.3.6.1.4.1.161.19.3.1.5.5.1
AP has exceeded the preset discard percentage in the RF Downlink Direction. rfOutDiscardRate - Current discard Rate. physAddress - the MAC address of the unit. |
| whispDefKeyUsed |
Object ID: 1.3.6.1.4.1.161.19.3.1.5.1.4
Signals Default Key used for encryptiont. |
| whispGPSInSync |
Object ID: 1.3.6.1.4.1.161.19.3.1.5.2.1
Signals a transition from not-synchronized to synchronized. |
| whispGPSOutSync |
Object ID: 1.3.6.1.4.1.161.19.3.1.5.2.2
Signals a transition from synchronized to not-synchronized. |
| whispRadarDetected |
Object ID: 1.3.6.1.4.1.161.19.3.1.5.3.1
Radar detected transmit stopped. |
| whispRadarEnd |
Object ID: 1.3.6.1.4.1.161.19.3.1.5.3.2
Radar ended back to normal transmit. |
| whispRegComplete |
Object ID: 1.3.6.1.4.1.161.19.3.1.5.1.1
Signals registration complete. |
| whispRegFailure |
Object ID: 1.3.6.1.4.1.161.19.3.1.5.1.3
Signals a registration failure has occured. |
| whispRegLost |
Object ID: 1.3.6.1.4.1.161.19.3.1.5.1.2
Signals registration lost. |
| Object Summary | |
| accountingInterimUpdateInterval |
Object ID: 1.3.6.1.4.1.161.19.3.1.1.106
Select Interval for Interim Updates |
| accountingSmReAuthInterval |
Object ID: 1.3.6.1.4.1.161.19.3.1.1.100
Select Interval for Reauthentication of SM |
| acctDomainNameAppend |
Object ID: 1.3.6.1.4.1.161.19.3.1.9.13
Obsoleted. Use whispApsDNS.authDomainNameAppend. |
| actDwnFragCount |
Object ID: 1.3.6.1.4.1.161.19.3.1.2.2.11
Actual Fragment Count |
| actDwnLinkIndex |
Object ID: 1.3.6.1.4.1.161.19.3.1.2.2.9
Actual down link index. |
| actUpFragCount |
Object ID: 1.3.6.1.4.1.161.19.3.1.2.2.14
Actual uplink Fragment Count. |
| actUpLinkIndex |
Object ID: 1.3.6.1.4.1.161.19.3.1.2.2.16
Actual Up link index. |
| actionListFilename |
Object ID: 1.3.6.1.4.1.161.19.3.1.1.98
Name of the file that contains the Action List for Auto update commands from CNUT |
| adaptRate |
Object ID: 1.3.6.1.4.1.161.19.3.1.4.1.40
Adapt rate of registered SM. |
| airLinkSecurity |
Object ID: 1.3.6.1.4.1.161.19.3.1.1.18
Air Link Security. desEnhancedAndAuthentication(2) and authenticationIfAvailable(3) are only for APAS. |
| allowedIPAccess1 |
Object ID: 1.3.6.1.4.1.161.19.3.1.1.46
Allow access to AP Management from this IP. 0 is default setting to allow from all IPs. |
| allowedIPAccess2 |
Object ID: 1.3.6.1.4.1.161.19.3.1.1.47
Allow access to AP Management from this IP. 0 is default setting to allow from all IPs. |
| allowedIPAccess3 |
Object ID: 1.3.6.1.4.1.161.19.3.1.1.48
Allow access to AP Management from this IP. 0 is default setting to allow from all IPs. |
| allowedIPAccessNMLength1 |
Object ID: 1.3.6.1.4.1.161.19.3.1.1.211
Length of the network mask to apply to the AllowedIPAddress when assessing if access is allowed |
| allowedIPAccessNMLength2 |
Object ID: 1.3.6.1.4.1.161.19.3.1.1.212
Length of the network mask to apply to the AllowedIPAddress when assessing if access is allowed |
| allowedIPAccessNMLength3 |
Object ID: 1.3.6.1.4.1.161.19.3.1.1.213
Length of the network mask to apply to the AllowedIPAddress when assessing if access is allowed |
| apBeaconInfo |
Object ID: 1.3.6.1.4.1.161.19.3.1.1.30
Variable to enable/disable displaying AP beacon info through AP eval. |
| apConfigAdjacentChanSupport |
Object ID: 1.3.6.1.4.1.161.19.3.1.1.220
Used to enable or disable adjacent channel support. |
| apLinkSpeed |
Object ID: 1.3.6.1.4.1.161.19.3.1.1.3
The variable is deprecated. |
| apRateAdapt |
Object ID: 1.3.6.1.4.1.161.19.3.1.1.41
To enable or disable double rate. |
| apRxDelay |
Object ID: 1.3.6.1.4.1.161.19.3.1.1.70
This is used for engineering debug and needs to be removed or moved to eng MIB before releasing the MIB. |
| apVlanOverride |
Object ID: 1.3.6.1.4.1.161.19.3.1.1.61
Setting this option will cause an AP to retain its VLAN settings when turning it into an SM. It will be mostly helpful for running spectrum analysis on the AP. Since doing that requires the AP to be turned into an SM, enabling this option will allow you to keep the AP's VLAN configuration in place while the AP is running as an SM. |
| asIP1 |
Object ID: 1.3.6.1.4.1.161.19.3.1.1.20
Obsoleted. Configure with whispApsDNS.authServer1. |
| asIP2 |
Object ID: 1.3.6.1.4.1.161.19.3.1.1.21
Obsoleted. Configure with whispApsDNS.authServer2. |
| asIP3 |
Object ID: 1.3.6.1.4.1.161.19.3.1.1.22
Obsoleted. Configure with whispApsDNS.authServer3. |
| asIP4 |
Object ID: 1.3.6.1.4.1.161.19.3.1.1.67
Obsoleted. Configure with whispApsDNS.authServer4. |
| asIP5 |
Object ID: 1.3.6.1.4.1.161.19.3.1.1.68
Obsoleted. Configure with whispApsDNS.authServer5. |
| authDomainNameAppend |
Object ID: 1.3.6.1.4.1.161.19.3.1.9.7
Select whether to append the configured management domain name to the configured trap names. For example, if dnsMgmtDomainName is set to 'example.com', authServer1 is set to 'auth1', and authDomainNameAppend is set to appendDomain, the authServer1 name used would be 'auth1.example.com'. |
| authKeyAp |
Object ID: 1.3.6.1.4.1.161.19.3.1.1.32
Authentication key. It should be 32 character long. Can be used on MultiPoint AP if AP Authentication mode is selected. Otherwise, it is used on Backhauls. |
| authKeyOptionAP |
Object ID: 1.3.6.1.4.1.161.19.3.1.1.66
This option is for Multipoint APs only. This option will only be used if Authentication Mode is set to AP Pre-Shared Key. 0 - Use default key. 1 - Use set key. |
| authMode |
Object ID: 1.3.6.1.4.1.161.19.3.1.1.31
Variable to enable/disable authentication. The authentication optional mode is for APs only. This variable can only be set when authentication feature is enabled. Setting it to 1 will use a BAM server for authentication of SMs. Setting it to 2 will make use of the Authentication Key on the AP for authenticating SMs. The keys must match on SM and AP in order for the SM to be authenticated in this mode. |
| authServer1 |
Object ID: 1.3.6.1.4.1.161.19.3.1.9.8
Authentication Server 1. Format is either an IP address or DNS name. |
| authServer2 |
Object ID: 1.3.6.1.4.1.161.19.3.1.9.9
Authentication Server 2. Format is either an IP address or DNS name. |
| authServer3 |
Object ID: 1.3.6.1.4.1.161.19.3.1.9.10
Authentication Server 3. Format is either an IP address or DNS name. |
| authServer4 |
Object ID: 1.3.6.1.4.1.161.19.3.1.9.11
Authentication Server 4. Format is either an IP address or DNS name. |
| authServer5 |
Object ID: 1.3.6.1.4.1.161.19.3.1.9.12
Authentication Server 5. Format is either an IP address or DNS name. |
| authSharedSecret1 |
Object ID: 1.3.6.1.4.1.161.19.3.1.1.74
Authentication Server 1 Shared Secret. |
| authSharedSecret2 |
Object ID: 1.3.6.1.4.1.161.19.3.1.1.75
Authentication Server 2 Shared Secret. |
| authSharedSecret3 |
Object ID: 1.3.6.1.4.1.161.19.3.1.1.76
Authentication Server 3 Shared Secret. |
| autoSyncStatus |
Object ID: 1.3.6.1.4.1.161.19.3.1.3.18
Current Live value of Sync Status. Following values represent what sources have sync. (0) No Sync (1) On-board GPS Sync (2) Timing Port/UGPS Sync (3) On-board GPS and Timing Port/UGPS Sync (4) Power Port Sync (5) On-board GPS and Power Port Sync (6) Timing Port/UGPS and Power Port Sync (7) On-board GPS, Timing Port/UGPS and Power Port Sync |
| autoUpdateGlobalStatus |
Object ID: 1.3.6.1.4.1.161.19.3.1.7.36
Status of the Auto-Update Command |
| autoUpdateStatus |
Object ID: 1.3.6.1.4.1.161.19.3.1.4.1.76
status of the auto update process |
| avgPowerLevel |
Object ID: 1.3.6.1.4.1.161.19.3.1.4.1.34
The average power level of registered SM. For systems that support power control, this value can read 'NA' when the AP adjusts the transmit power of a SM until new packets are received from the SM with it transmitting at its new power level. For MIMO this is the combined receive power. |
| berModSelect |
Object ID: 1.3.6.1.4.1.161.19.3.1.1.215
The modulation the AP generates BER at. 0 for QPSK, 1 for 16-QAM, 2 for 64-QAM, and 3 for 256-QAM. |
| berMode |
Object ID: 1.3.6.1.4.1.161.19.3.1.1.19
AP backgroup BER mode. |
| bhReReg |
Object ID: 1.3.6.1.4.1.161.19.3.1.1.58
Allows BHS re-registration every 24 hours. Enable allows re-registration and Disable does not. 24 Hour Encryption Refresh. |
| bitErrorsCorrected1xDwnLinkHorizontal |
Object ID: 1.3.6.1.4.1.161.19.3.1.2.2.43
Number of bit errors corrected on average per fragment on down link at 1X (QPSK). For MIMO and forward. For MIMO this is the horizontal path. Fragments received in MIMO-A will only be counted on vertical. |
| bitErrorsCorrected1xDwnLinkVertical |
Object ID: 1.3.6.1.4.1.161.19.3.1.2.2.25
Number of bit errors corrected on average per fragment on down link at 1X (QPSK). For Gen II OFDM and forward. For MIMO this is the vertical path. |
| bitErrorsCorrected1xUpLinkHorizontal |
Object ID: 1.3.6.1.4.1.161.19.3.1.2.2.47
Number of bit errors corrected on average per fragment on up link at 1X (QPSK). For MIMO and forward. For MIMO this is the horizontal path. Fragments received in MIMO-A will only be counted on vertical. |
| bitErrorsCorrected1xUpLinkVertical |
Object ID: 1.3.6.1.4.1.161.19.3.1.2.2.29
Number of bit errors corrected on average per fragment on up link at 1X (QPSK). For Gen II OFDM and forward. For MIMO this is the vertical path. |
| bitErrorsCorrected2xDwnLinkHorizontal |
Object ID: 1.3.6.1.4.1.161.19.3.1.2.2.44
Number of bit errors corrected on average per fragment on down link at 2X (16-QAM). For MIMO and forward. For MIMO this is the horizontal path. Fragments received in MIMO-A will only be counted on vertical. |
| bitErrorsCorrected2xDwnLinkVertical |
Object ID: 1.3.6.1.4.1.161.19.3.1.2.2.26
Number of bit errors corrected on average per fragment on down link at 2X (16-QAM). For Gen II OFDM and forward. For MIMO this is the vertical path. |
| bitErrorsCorrected2xUpLinkHorizontal |
Object ID: 1.3.6.1.4.1.161.19.3.1.2.2.48
Number of bit errors corrected on average per fragment on up link at 2X (16-QAM). For MIMO and forward. For MIMO this is the horizontal path. Fragments received in MIMO-A will only be counted on vertical. |
| bitErrorsCorrected2xUpLinkVertical |
Object ID: 1.3.6.1.4.1.161.19.3.1.2.2.30
Number of bit errors corrected on average per fragment on up link at 2X (16-QAM). For Gen II OFDM and forward. For MIMO this is the vertical path. |
| bitErrorsCorrected3xDwnLinkHorizontal |
Object ID: 1.3.6.1.4.1.161.19.3.1.2.2.45
Number of bit errors corrected on average per fragment on down link at 3X (64-QAM). For MIMO and forward. For MIMO this is the horizontal path. Fragments received in MIMO-A will only be counted on vertical. |
| bitErrorsCorrected3xDwnLinkVertical |
Object ID: 1.3.6.1.4.1.161.19.3.1.2.2.27
Number of bit errors corrected on average per fragment on down link at 3X (64-QAM). For Gen II OFDM and forward. For MIMO this is the vertical path. |
| bitErrorsCorrected3xUpLinkHorizontal |
Object ID: 1.3.6.1.4.1.161.19.3.1.2.2.49
Engineering use only. Number of bit errors corrected on average per fragment on up link at 3X (64-QAM). For MIMO and forward. For MIMO this is the horizontal path. Fragments received in MIMO-A will only be counted on vertical. |
| bitErrorsCorrected3xUpLinkVertical |
Object ID: 1.3.6.1.4.1.161.19.3.1.2.2.31
Number of bit errors corrected on average per fragment on up link at 3X (64-QAM). For Gen II OFDM and forward. For MIMO this is the vertical path. |
| bitErrorsCorrected4xDwnLinkHorizontal |
Object ID: 1.3.6.1.4.1.161.19.3.1.2.2.46
Number of bit errors corrected on average per fragment on down link at 4X (256-QAM). For MIMO and forward. For MIMO this is the horizontal path. Fragments received in MIMO-A will only be counted on vertical. |
| bitErrorsCorrected4xDwnLinkVertical |
Object ID: 1.3.6.1.4.1.161.19.3.1.2.2.28
Number of bit errors corrected on average per fragment on down link at 4X (256-QAM). For Gen II OFDM and forward. For MIMO this is the vertical path. |
| bitErrorsCorrected4xUpLinkHorizontal |
Object ID: 1.3.6.1.4.1.161.19.3.1.2.2.50
Number of bit errors corrected on average per fragment on up link at 4X (256-QAM). For MIMO and forward. For MIMO this is the horizontal path. Fragments received in MIMO-A will only be counted on vertical. |
| bitErrorsCorrected4xUpLinkVertical |
Object ID: 1.3.6.1.4.1.161.19.3.1.2.2.32
Number of bit errors corrected on average per fragment on up link at 4X (256-QAM). For Gen II OFDM and forward. For MIMO this is the vertical path. |
| bridgeFloodUnknownsEnable |
Object ID: 1.3.6.1.4.1.161.19.3.1.1.214
To enable or disable bridge flooding unknown unicast packets. (0) - Bridge will not forward unknown unicast packets. (1) - Bridge will flood unknown unicast packets. |
| broadcastRetryCount |
Object ID: 1.3.6.1.4.1.161.19.3.1.1.35
Broadcast Repeat Count : Range 0 -- 2. For APs. |
| clearLinkTableStats |
Object ID: 1.3.6.1.4.1.161.19.3.1.11.1
Setting this to a nonzero value will clear the link table stats. |
| colorCodeRescanIdleTimer |
Object ID: 1.3.6.1.4.1.161.19.3.1.1.65
Time in minutes for the subscriber to check for an idle state. If an period has pass where no unicast RF traffic has occured (idle), then the subscriber will begin to rescan. This timer will wait until the timer set in colorCodeRescanTimer has expired before beginning. This timer only fires if the device is in session with a non-primary color code. A value of zero (0) mean to rescan without waiting for idle. (MultiPoint system Only) |
| colorCodeRescanTimer |
Object ID: 1.3.6.1.4.1.161.19.3.1.1.64
Time in minutes for the subscriber to begin the idle timer. This timer will begin as soon as a session is started. This only fires if the device is in session with a non-primary color code. A value of zero (0) disables this timer (MultiPoint system Only) |
| configSource |
Object ID: 1.3.6.1.4.1.161.19.3.1.1.40
To configure CIR, MIR and VLAN through SM or BAM. |
| currentRadioFreqCarrier |
Object ID: 1.3.6.1.4.1.161.19.3.1.7.37
Returns the current operating frequency of the AP. Units vary by platform: FSK 5.2, 5.4, 5.7 GHz: OID returns MHz FSK 900 MHz, 2.4 GHz: OID returns 100's of KHz OFDM: OID returns 10's of KHz |
| dAcksReservHigh |
Object ID: 1.3.6.1.4.1.161.19.3.1.1.9
Total number of high priority downstream ack slots. |
| dataSlotDwn |
Object ID: 1.3.6.1.4.1.161.19.3.1.7.5
Number of data slot down. |
| dataSlotUp |
Object ID: 1.3.6.1.4.1.161.19.3.1.7.6
Number of data slot up. |
| dataSlotUpHi |
Object ID: 1.3.6.1.4.1.161.19.3.1.7.7
Number of high priority data slot up. |
| dataVCNum |
Object ID: 1.3.6.1.4.1.161.19.3.1.4.1.48
The normal priority Data VC number in use for this link. |
| dataVCNumHiQ |
Object ID: 1.3.6.1.4.1.161.19.3.1.4.1.50
The high priority Data VC number in use for this link, if any. If 0, no High Priority channel is in place. |
| defaultGwAp |
Object ID: 1.3.6.1.4.1.161.19.3.1.1.25
Default gateway |
| dfsConfig |
Object ID: 1.3.6.1.4.1.161.19.3.1.1.38
To configure proper regions for Dynamic Frequency Shifting. For 5.2/5.4/5.7 GHz radios. |
| dfsStatus |
Object ID: 1.3.6.1.4.1.161.19.3.1.7.14
Dynamic frequency shifting status. |
| dfsStatusAlt1 |
Object ID: 1.3.6.1.4.1.161.19.3.1.7.16
Dynamic frequency shifting status for Alternate Channel 1 |
| dfsStatusAlt2 |
Object ID: 1.3.6.1.4.1.161.19.3.1.7.17
Dynamic frequency shifting status for Alternate Channel 2 |
| dfsStatusPrimary |
Object ID: 1.3.6.1.4.1.161.19.3.1.7.15
Dynamic frequency shifting status for Primary Channel. |
| dhcpRelayAgentEnable |
Object ID: 1.3.6.1.4.1.161.19.3.1.1.62
Enable or Disable MultiPoint AP acting as DHCP Relay Agent for all SMs and Clients underneath it. (0) - Relay Agent disabled - SM/CPE devices will perform DHCP normally (1) - Relay Agent enabled - AP will intercept DHCP DISCOVER message from SM and CPE, insert Option 82 containing SM's MAC address, and forward request to specified DHCP server. |
| dhcpRelayAgentSrvrIP |
Object ID: 1.3.6.1.4.1.161.19.3.1.1.63
Obsoleted. Configure with whispApsDNS.dhcprServer. |
| dhcpRlyAgntStat-invalidGiaddrDiscards |
Object ID: 1.3.6.1.4.1.161.19.3.1.7.31
Number of messages discarded by the DHCP Relay due to invalid giaddr in packet. |
| dhcpRlyAgntStat-maxHopDiscards |
Object ID: 1.3.6.1.4.1.161.19.3.1.7.29
Number of messages discarded by the DHCP Relay due to exceeded max hop. |
| dhcpRlyAgntStat-pktTooBig |
Object ID: 1.3.6.1.4.1.161.19.3.1.7.30
Number of messages forwarded without relay information by the DHCP Relay due to relay information exceeding max message size. |
| dhcpRlyAgntStat-reqDiscards |
Object ID: 1.3.6.1.4.1.161.19.3.1.7.24
Number of DHCP Requests discarded by the DHCP Relay. |
| dhcpRlyAgntStat-reqRecvd |
Object ID: 1.3.6.1.4.1.161.19.3.1.7.22
Number of DHCP Requests received by the DHCP Relay. |
| dhcpRlyAgntStat-reqRelayed |
Object ID: 1.3.6.1.4.1.161.19.3.1.7.23
Number of DHCP Requests relayed by the DHCP Relay. |
| dhcpRlyAgntStat-respDiscards |
Object ID: 1.3.6.1.4.1.161.19.3.1.7.27
Number of DHCP Replies discarded by the DHCP Relay. |
| dhcpRlyAgntStat-respRecvd |
Object ID: 1.3.6.1.4.1.161.19.3.1.7.25
Number of DHCP Replies received by the DHCP Relay. |
| dhcpRlyAgntStat-respRelayed |
Object ID: 1.3.6.1.4.1.161.19.3.1.7.26
Number of DHCP Replies relayed by the DHCP Relay. |
| dhcpRlyAgntStat-untrustedDiscards |
Object ID: 1.3.6.1.4.1.161.19.3.1.7.28
Number of untrusted messages discarded by the DHCP Relay. |
| dhcprDomainNameAppend |
Object ID: 1.3.6.1.4.1.161.19.3.1.9.5
Select whether to append the configured management domain name to the configured trap names. For example, if dnsMgmtDomainName is set to 'example.com', dhcprServer is set to 'dhcpr', and dhcprDomainNameAppend is set to appendDomain, the dhcprServer name used would be 'dhcpr.example.com'. |
| dhcprServer |
Object ID: 1.3.6.1.4.1.161.19.3.1.9.6
DHCP Server IP which will be used for forwarding DHCP messages by the DHCP Relay Agent in the MultiPoint AP. - Format is either an IP address or DNS name. - Default is 255.255.255.255 (broadcast). |
| displayAPEval |
Object ID: 1.3.6.1.4.1.161.19.3.1.1.43
If enable, it allows display of AP Eval Data at the SM. |
| dlnkBcastCIR |
Object ID: 1.3.6.1.4.1.161.19.3.1.1.59
Downlink Broadcast CIR (kbps) |
| dlnkMcastCIR |
Object ID: 1.3.6.1.4.1.161.19.3.1.1.218
Downlink Multicast CIR (kbps) |
| downLinkEff |
Object ID: 1.3.6.1.4.1.161.19.3.1.2.2.7
Down Link Efficiency. |
| downLinkRate |
Object ID: 1.3.6.1.4.1.161.19.3.1.2.2.5
Down Link Rate. |
| dropSession |
Object ID: 1.3.6.1.4.1.161.19.3.1.1.87
SM/BHS MAC Address to drop session from the AP/BHM. |
| dwnLnkAckSlot |
Object ID: 1.3.6.1.4.1.161.19.3.1.7.10
Downlink ack slots. |
| dwnLnkAckSlotHi |
Object ID: 1.3.6.1.4.1.161.19.3.1.7.11
Hige priority downlink ack slots. |
| dwnLnkData |
Object ID: 1.3.6.1.4.1.161.19.3.1.1.4
This attribute is deprecated. Please see radioDownlinkPercent. |
| dwnLnkDataRate |
Object ID: 1.3.6.1.4.1.161.19.3.1.1.14
Sustained downlink bandwidth cap. |
| dwnLnkLimit |
Object ID: 1.3.6.1.4.1.161.19.3.1.1.15
Burst downlink bandwidth cap. |
| dwnLnkMaxBurstDataRate |
Object ID: 1.3.6.1.4.1.161.19.3.1.1.209
Maximum burst downlink rate. |
| enableAutoupdate |
Object ID: 1.3.6.1.4.1.161.19.3.1.1.99
Enables/Disables auto-update of the SM's under an AP |
| encryptDwBroadcast |
Object ID: 1.3.6.1.4.1.161.19.3.1.1.36
To enable or disable Encrypted Downlink Broadcast. For FSK APs. |
| encryptionMode |
Object ID: 1.3.6.1.4.1.161.19.3.1.1.33
Variable to enable/disable encryption. |
| expDwnFragCount |
Object ID: 1.3.6.1.4.1.161.19.3.1.2.2.10
Expected Fragment Count. |
| expUpFragCount |
Object ID: 1.3.6.1.4.1.161.19.3.1.2.2.13
Uplink expected Fragment Count. |
| fpgaVersion |
Object ID: 1.3.6.1.4.1.161.19.3.1.4.1.32
The FPGA version of registered SM. |
| fragments1xDwnLinkHorizontal |
Object ID: 1.3.6.1.4.1.161.19.3.1.2.2.35
Number of fragments received on down link at 1X (QPSK). For MIMO only. For MIMO this is the horizontal path. Fragments received in MIMO-A will only be counted on vertical. |
| fragments1xDwnLinkVertical |
Object ID: 1.3.6.1.4.1.161.19.3.1.2.2.17
Number of fragments received on down link at 1X (QPSK). For Gen II OFDM and forward. For MIMO this is the vertical path. |
| fragments1xUpLinkHorizontal |
Object ID: 1.3.6.1.4.1.161.19.3.1.2.2.39
Number of fragments received on up link at 1X (QPSK). For MIMO only. For MIMO this is the horizontal path. Fragments received in MIMO-A will only be counted on vertical. |
| fragments1xUpLinkVertical |
Object ID: 1.3.6.1.4.1.161.19.3.1.2.2.21
Number of fragments received on up link at 1X (QPSK). For Gen II OFDM and forward. For MIMO this is the vertical path. |
| fragments2xDwnLinkHorizontal |
Object ID: 1.3.6.1.4.1.161.19.3.1.2.2.36
Number of fragments received on down link at 2X (16-QAM). For MIMO only. For MIMO this is the horizontal path. Fragments received in MIMO-A will only be counted on vertical. |
| fragments2xDwnLinkVertical |
Object ID: 1.3.6.1.4.1.161.19.3.1.2.2.18
Number of fragments received on down link at 2X (16-QAM). For Gen II OFDM and forward. For MIMO this is the vertical path. |
| fragments2xUpLinkHorizontal |
Object ID: 1.3.6.1.4.1.161.19.3.1.2.2.40
Number of fragments received on up link at 2X (16-QAM). For MIMO only. For MIMO this is the horizontal path. Fragments received in MIMO-A will only be counted on vertical. |
| fragments2xUpLinkVertical |
Object ID: 1.3.6.1.4.1.161.19.3.1.2.2.22
Number of fragments received on up link at 2X (16-QAM). For Gen II OFDM and forward. For MIMO this is the vertical path. |
| fragments3xDwnLinkHorizontal |
Object ID: 1.3.6.1.4.1.161.19.3.1.2.2.37
Number of fragments received on down link at 3X (64-QAM). For MIMO only. For MIMO this is the horizontal path. Fragments received in MIMO-A will only be counted on vertical. |
| fragments3xDwnLinkVertical |
Object ID: 1.3.6.1.4.1.161.19.3.1.2.2.19
Number of fragments received on down link at 3X (64-QAM). For Gen II OFDM and forward. For MIMO this is the vertical path. |
| fragments3xUpLinkHorizontal |
Object ID: 1.3.6.1.4.1.161.19.3.1.2.2.41
Number of fragments received on up link at 3X (64-QAM). For MIMO only. For MIMO this is the horizontal path. Fragments received in MIMO-A will only be counted on vertical. |
| fragments3xUpLinkVertical |
Object ID: 1.3.6.1.4.1.161.19.3.1.2.2.23
Number of fragments received on up link at 3X (64-QAM). For Gen II OFDM and forward. For MIMO this is the vertical path. |
| fragments4xDwnLinkHorizontal |
Object ID: 1.3.6.1.4.1.161.19.3.1.2.2.38
Number of fragments received on down link at 4X (256-QAM). For MIMO only. For MIMO this is the horizontal path. Fragments received in MIMO-A will only be counted on vertical. |
| fragments4xDwnLinkVertical |
Object ID: 1.3.6.1.4.1.161.19.3.1.2.2.20
Number of fragments received on down link at 4X (256-QAM). For Gen II OFDM and forward. For MIMO this is the vertical path. |
| fragments4xUpLinkHorizontal |
Object ID: 1.3.6.1.4.1.161.19.3.1.2.2.42
Number of fragments received on up link at 4X (256-QAM). For MIMO only. For MIMO this is the horizontal path. Fragments received in MIMO-A will only be counted on vertical. |
| fragments4xUpLinkVertical |
Object ID: 1.3.6.1.4.1.161.19.3.1.2.2.24
Number of fragments received on up link at 4X (256-QAM). For Gen II OFDM and forward. For MIMO this is the vertical path. |
| fskSMRcvTargetLvl |
Object ID: 1.3.6.1.4.1.161.19.3.1.1.73
Desired SM Receive Level at AP (dBm, Range -40dBm to -80 dBm). |
| fskSMTxPwrCntl |
Object ID: 1.3.6.1.4.1.161.19.3.1.1.72
Enable/Disable AP control of SM TX power. For FSK AP radios capable of Transmit Power Control. |
| gpsAntennaConnection |
Object ID: 1.3.6.1.4.1.161.19.3.1.3.10
Antenna Connection status. |
| gpsDate |
Object ID: 1.3.6.1.4.1.161.19.3.1.3.6
GPS date. |
| gpsFreeRun |
Object ID: 1.3.6.1.4.1.161.19.3.1.3.17
This variable is deprecated. Setting this value to false will set AutoSync. Setting this value to true will set AutoSync plus Free Run. |
| gpsHeight |
Object ID: 1.3.6.1.4.1.161.19.3.1.3.9
GPS height. |
| gpsInput |
Object ID: 1.3.6.1.4.1.161.19.3.1.1.1
The variable is deprecated. See gpsInput in whispBoxConfig. |
| gpsInvalidMsg |
Object ID: 1.3.6.1.4.1.161.19.3.1.3.13
Number of invalid messages. |
| gpsLatitude |
Object ID: 1.3.6.1.4.1.161.19.3.1.3.11
GPS Latitude. |
| gpsLongitude |
Object ID: 1.3.6.1.4.1.161.19.3.1.3.12
GPS Longitude. |
| gpsOutputEn |
Object ID: 1.3.6.1.4.1.161.19.3.1.1.107
Enable or Disable GPS sync output enable. |
| gpsReInitCount |
Object ID: 1.3.6.1.4.1.161.19.3.1.3.15
GPS ReInit counts. The number of times we have done a complete re-initialization of the GPS device. |
| gpsReceiverInfo |
Object ID: 1.3.6.1.4.1.161.19.3.1.3.16
A textual string contains information on GPS receiver. |
| gpsRestartCount |
Object ID: 1.3.6.1.4.1.161.19.3.1.3.14
Number of GPS unit restarts. |
| gpsSatellitesTracked |
Object ID: 1.3.6.1.4.1.161.19.3.1.3.7
Returns Current number of satellites GPS is tracking in string format .use gpsSatellitesTrackedInt to get the value in integer |
| gpsSatellitesTrackedInt |
Object ID: 1.3.6.1.4.1.161.19.3.1.3.19
Current number of satellites GPS is tracking in integer format. |
| gpsSatellitesVisible |
Object ID: 1.3.6.1.4.1.161.19.3.1.3.8
Return Number of satellites GPS is seeing in string format.Use gpsSatellitesVisibleInt to get value in integer |
| gpsSatellitesVisibleInt |
Object ID: 1.3.6.1.4.1.161.19.3.1.3.20
Number of satellites the GPS sees in integer format |
| gpsStatus |
Object ID: 1.3.6.1.4.1.161.19.3.1.7.2
GPS status. |
| gpsSyncSource |
Object ID: 1.3.6.1.4.1.161.19.3.1.3.2
Source of GPS Sync Pulse. |
| gpsSyncStatus |
Object ID: 1.3.6.1.4.1.161.19.3.1.3.3
Current Live value of Sync Status. |
| gpsTime |
Object ID: 1.3.6.1.4.1.161.19.3.1.3.5
GPS time. |
| gpsTrackingMode |
Object ID: 1.3.6.1.4.1.161.19.3.1.3.4
GPS tracking mode. |
| gpsTrap |
Object ID: 1.3.6.1.4.1.161.19.3.1.1.27
Variable to enable/disable GPS sync/out-sync traps. |
| hiPriQEn |
Object ID: 1.3.6.1.4.1.161.19.3.1.4.1.49
Returns whether High Priority channel is enabled. On P7/P8 devices will return 0 always. Use p7p8HiPriQEn OID for P7/P8 radios. |
| highPriorityUpLnkPct |
Object ID: 1.3.6.1.4.1.161.19.3.1.1.5
Percentage of uplink slots for high priority data. |
| ipAccessFilterEnable |
Object ID: 1.3.6.1.4.1.161.19.3.1.1.45
To enable or disable IP access filtering to Management functions. (0) - IP access will be allowed from all addresses. (1) - IP access will be controlled using allowedIPAccess1-3 entries. |
| lanIpAp |
Object ID: 1.3.6.1.4.1.161.19.3.1.1.23
LAN IP. |
| lanMaskAp |
Object ID: 1.3.6.1.4.1.161.19.3.1.1.24
LAN subnet mask. |
| lastNTPTime |
Object ID: 1.3.6.1.4.1.161.19.3.1.7.20
Displays the last NTP time acquired by the AP |
| lastPowerLevel |
Object ID: 1.3.6.1.4.1.161.19.3.1.4.1.35
The last power level of registered SM. For MIMO radios this is the combined receive power. |
| lastSesStatsReset |
Object ID: 1.3.6.1.4.1.161.19.3.1.1.93
Displays the timestamp of last reset of session stats or None otherwise. |
| limitFreqBand900 |
Object ID: 1.3.6.1.4.1.161.19.3.1.1.51
1 = We are limiting the freq band of 900 radios. 0 = We are not. |
| linkAdaptRateHighPri |
Object ID: 1.3.6.1.4.1.161.19.3.1.4.1.92
The current transmitting rate of the high priority VC. -1 : High Priority Channel not configured 0 : SM is not in session 1 : 1X QPSK SISO 2 : 2X 16-QAM SISO or QPSK MIMO 3 : 3X 64-QAM SISO 4 : 4X 256-QAM SISO or 16-QAM MIMO 6 : 6X 64-QAM MIMO 8 : 8X 256-QAM MIMO |
| linkAdaptRateLowPri |
Object ID: 1.3.6.1.4.1.161.19.3.1.4.1.91
The current transmitting rate of the low priority VC. 0 : SM is not in session 1 : 1X QPSK SISO 2 : 2X 16-QAM SISO or QPSK MIMO 3 : 3X 64-QAM SISO 4 : 4X 256-QAM SISO or 16-QAM MIMO 6 : 6X 64-QAM MIMO 8 : 8X 256-QAM MIMO |
| linkAirDelay |
Object ID: 1.3.6.1.4.1.161.19.3.1.4.1.24
The current round trip air delay in bits measured between the AP and SM. |
| linkAirDelayns |
Object ID: 1.3.6.1.4.1.161.19.3.1.4.1.66
The current round trip air delay in nanoseconds measured between the AP and SM. |
| linkAveJitter |
Object ID: 1.3.6.1.4.1.161.19.3.1.4.1.22
The average Jitter reading of all packets received from an SM. Applicable to FSK radios only. |
| linkDescr |
Object ID: 1.3.6.1.4.1.161.19.3.1.4.1.2
A textual string containing information about the unit. This string should include the name of the manufacturer, the product name and the version of the hardware interface. |
| linkESN |
Object ID: 1.3.6.1.4.1.161.19.3.1.4.1.20
Link Electronic serial number. It is MAC address. |
| linkFragmentsReceived1XHorizontal |
Object ID: 1.3.6.1.4.1.161.19.3.1.4.1.80
Engineering use only. Number of fragments received in 1x (QPSK) modulation. For MIMO only. For MIMO this is the horizontal path. If operating in MIMO-A this will return 0. |
| linkFragmentsReceived1XVertical |
Object ID: 1.3.6.1.4.1.161.19.3.1.4.1.70
Engineering use only. Number of fragments received in 1x (QPSK) modulation. For GenII OFDM and forward. For MIMO this is the vertical path. |
| linkFragmentsReceived2XHorizontal |
Object ID: 1.3.6.1.4.1.161.19.3.1.4.1.81
Engineering use only. Number of fragments received in 2x (16-QAM) modulation. For MIMO only. For MIMO this is the horizontal path. If operating in MIMO-A this will return 0. |
| linkFragmentsReceived2XVertical |
Object ID: 1.3.6.1.4.1.161.19.3.1.4.1.71
Engineering use only. Number of fragments received in 2x (16-QAM) modulation. For GenII OFDM and forward. For MIMO this is the vertical path. |
| linkFragmentsReceived3XHorizontal |
Object ID: 1.3.6.1.4.1.161.19.3.1.4.1.82
Engineering use only. Number of fragments received in 3x (64-QAM) modulation. For MIMO only. For MIMO this is the horizontal path. If operating in MIMO-A this will return 0. |
| linkFragmentsReceived3XVertical |
Object ID: 1.3.6.1.4.1.161.19.3.1.4.1.72
Engineering use only. Number of fragments received in 3x (64-QAM) modulation. For GenII OFDM and forward. For MIMO this is the vertical path. |
| linkFragmentsReceived4XHorizontal |
Object ID: 1.3.6.1.4.1.161.19.3.1.4.1.83
Engineering use only. Number of fragments received in 4x (256-QAM) modulation. For MIMO only. For MIMO this is the horizontal path. If operating in MIMO-A this will return 0. |
| linkFragmentsReceived4XVertical |
Object ID: 1.3.6.1.4.1.161.19.3.1.4.1.73
Engineering use only. Number of fragments received in 4x (256-QAM) modulation. For GenII OFDM and forward. For MIMO this is the vertical path. |
| linkInDiscards |
Object ID: 1.3.6.1.4.1.161.19.3.1.4.1.10
The number of inbound packets which were chosen to be discarded even though no errors had been detected to prevent their being deliverable to a higher-layer protocol. One possible reason for discarding such a packet could be to free up buffer space. |
| linkInDiscardsHiQ |
Object ID: 1.3.6.1.4.1.161.19.3.1.4.1.54
The number of inbound packets on High Priority Queue which were chosen to be discarded even though no errors had been detected to prevent their being deliverable to a higher-layer protocol. One possible reason for discarding such a packet could be to free up buffer space. |
| linkInError |
Object ID: 1.3.6.1.4.1.161.19.3.1.4.1.11
The number of inbound packets that contained errors preventing them from being deliverable to a higher-layer protocol. |
| linkInErrorHiQ |
Object ID: 1.3.6.1.4.1.161.19.3.1.4.1.55
The number of inbound packets on High Priority Queue that contained errors preventing them from being deliverable to a higher-layer protocol. |
| linkInNUcastPkts |
Object ID: 1.3.6.1.4.1.161.19.3.1.4.1.9
The number of non-unicast (i.e., subnetwork- broadcast or subnetwork-multicast) packets delivered to a higher-layer protocol. |
| linkInNUcastPktsHiQ |
Object ID: 1.3.6.1.4.1.161.19.3.1.4.1.53
The number of non-unicast (i.e., subnetwork- broadcast or subnetwork-multicast) packets on High Priority Queue delivered to a higher-layer protocol. |
| linkInOctets |
Object ID: 1.3.6.1.4.1.161.19.3.1.4.1.7
The total number of octets received on the interface, including framing characters. |
| linkInOctetsHiQ |
Object ID: 1.3.6.1.4.1.161.19.3.1.4.1.51
The total number of octets received on High Priority Queue, including framing characters. |
| linkInUcastPkts |
Object ID: 1.3.6.1.4.1.161.19.3.1.4.1.8
The number of subnetwork-unicast packets delivered to a higher-layer protocol. |
| linkInUcastPktsHiQ |
Object ID: 1.3.6.1.4.1.161.19.3.1.4.1.52
The number of subnetwork-unicast packets on High Priority Queue delivered to a higher-layer protocol. |
| linkInUnknownProtos |
Object ID: 1.3.6.1.4.1.161.19.3.1.4.1.12
The number of packets received via the interface which were discarded because of an unknown or unsupported protocol. |
| linkInUnknownProtosHiQ |
Object ID: 1.3.6.1.4.1.161.19.3.1.4.1.56
The number of packets received on High Priority Queue via the interface which were discarded because of an unknown or unsupported protocol. |
| linkLUID |
Object ID: 1.3.6.1.4.1.161.19.3.1.4.1.1
LUID number. |
| linkLastJitter |
Object ID: 1.3.6.1.4.1.161.19.3.1.4.1.23
Last jitter value. Applicable to FSK radios only. |
| linkLastRSSI |
Object ID: 1.3.6.1.4.1.161.19.3.1.4.1.28
The last RSSI reading of all packets received from an SM. Applicable to FSK radios only. |
| linkManagementIP |
Object ID: 1.3.6.1.4.1.161.19.3.1.4.1.69
Management IP Address of the unit. 0 indicates SM is not publically addressable. |
| linkMtu |
Object ID: 1.3.6.1.4.1.161.19.3.1.4.1.4
The size of the largest datagram which can be sent/received on the interface, specified in octets. For interfaces that are used for transmitting network datagrams, this is the size of the largest network datagram that can be sent on the interface. |
| linkOperStatus |
Object ID: 1.3.6.1.4.1.161.19.3.1.4.1.6
This variable is not used. |
| linkOutDiscards |
Object ID: 1.3.6.1.4.1.161.19.3.1.4.1.16
The number of outbound packets which were chosen to be discarded even though no errors had been detected to prevent their being transmitted. One possible reason for discarding such a packet could be to free up buffer space. |
| linkOutDiscardsHiQ |
Object ID: 1.3.6.1.4.1.161.19.3.1.4.1.60
The number of outbound packets on High Priority Queue which were chosen to be discarded even though no errors had been detected to prevent their being transmitted. One possible reason for discarding such a packet could be to free up buffer space. |
| linkOutError |
Object ID: 1.3.6.1.4.1.161.19.3.1.4.1.17
The number of outbound packets that could not be transmitted because of errors. |
| linkOutErrorHiQ |
Object ID: 1.3.6.1.4.1.161.19.3.1.4.1.61
The number of outbound packets on High Priority Queue that could not be transmitted because of errors. |
| linkOutNUcastPkts |
Object ID: 1.3.6.1.4.1.161.19.3.1.4.1.15
The total number of packets that higher-level protocols requested be transmitted to a non- unicast (i.e., a subnetwork-broadcast or subnetwork-multicast) address, including those that were discarded or not sent. |
| linkOutNUcastPktsHiQ |
Object ID: 1.3.6.1.4.1.161.19.3.1.4.1.59
The total number of packets on High Priority Queue that higher-level protocols requested be transmitted to a non- unicast (i.e., a subnetwork-broadcast or subnetwork-multicast) address, including those that were discarded or not sent. |
| linkOutOctets |
Object ID: 1.3.6.1.4.1.161.19.3.1.4.1.13
The total number of octets transmitted out of the interface, including framing characters. |
| linkOutOctetsHiQ |
Object ID: 1.3.6.1.4.1.161.19.3.1.4.1.57
The total number of octets on High Priority Queue transmitted out of the interface, including framing characters. |
| linkOutQLen |
Object ID: 1.3.6.1.4.1.161.19.3.1.4.1.18
Number of packets in output packet queue. |
| linkOutUcastPkts |
Object ID: 1.3.6.1.4.1.161.19.3.1.4.1.14
The total number of packets that higher-level protocols requested be transmitted to a subnetwork-unicast address, including those that were discarded or not sent. |
| linkOutUcastPktsHiQ |
Object ID: 1.3.6.1.4.1.161.19.3.1.4.1.58
The total number of packets on High Priority Queue that higher-level protocols requested be transmitted to a subnetwork-unicast address, including those that were discarded or not sent. |
| linkPhysAddress |
Object ID: 1.3.6.1.4.1.161.19.3.1.4.1.3
Physical Address of the unit. |
| linkQualityAPData |
Object ID: 1.3.6.1.4.1.161.19.3.1.4.1.67
The current link quality of the SM's data from the AP. This is relative to the current modulation rate (1X, 2X, 3X, etc). |
| linkRSSI |
Object ID: 1.3.6.1.4.1.161.19.3.1.4.1.21
The average RSSI reading of all packets received from an SM. Applicable to FSK radios only. |
| linkRadioDbmHorizontal |
Object ID: 1.3.6.1.4.1.161.19.3.1.4.1.87
Receive power level of the horizontal antenna in dBm. MIMO radios only. |
| linkRadioDbmVertical |
Object ID: 1.3.6.1.4.1.161.19.3.1.4.1.88
Receive power level of the vertical antenna in dBm. MIMO radios only. |
| linkReRegCount |
Object ID: 1.3.6.1.4.1.161.19.3.1.4.1.26
The number of times an SM has tried to register with the AP while it still has an active session with the AP. |
| linkRegCount |
Object ID: 1.3.6.1.4.1.161.19.3.1.4.1.25
The number of times an SM has registered to an AP. |
| linkSessState |
Object ID: 1.3.6.1.4.1.161.19.3.1.4.1.19
Current operational state of an interface. 0 = Idle 1 = In Session 2 = Clearing 3 = Re-registration downlink reset 4 = Authentication Challenge 5 = Registering 6 = Not in use |
| linkSignalStrengthRatio |
Object ID: 1.3.6.1.4.1.161.19.3.1.4.1.86
Signal Strength Ratio in dB is the power received by the vertical antenna input (dB) - power received by the horizontal antenna input (dB). MIMO radios only. |
| linkSiteName |
Object ID: 1.3.6.1.4.1.161.19.3.1.4.1.33
The site name of the registered SM. |
| linkSpeed |
Object ID: 1.3.6.1.4.1.161.19.3.1.4.1.5
An estimate of the interface's current bandwidth in bits per second. For interfaces which do not vary in bandwidth or for those where no accurate estimation can be made, this object should contain the nominal bandwidth. |
| linkTestAction |
Object ID: 1.3.6.1.4.1.161.19.3.1.2.1.3
Setting value 1 will initiate link test. Note that trying to set 0 will not stop the test. In fact it will return an error message. The value of 0 just indicates the idle state meaning no test is running or the current test is done. That's why the word stopped is used and not the action verb stop. |
| linkTestDirection |
Object ID: 1.3.6.1.4.1.161.19.3.1.2.1.10
Link Test Direction - Engineering Use Only 0 = not set - default (will do bidirectional) 1 = Downlink Only 2 = Uplink Only 3 = Bi-Directional (same as 0, setting to 0 will result in setting it to 3) |
| linkTestDuration |
Object ID: 1.3.6.1.4.1.161.19.3.1.2.1.2
Duration for the Link Test. Valid range: 2-10 seconds |
| linkTestError |
Object ID: 1.3.6.1.4.1.161.19.3.1.2.2.3
Error status of Link Test: (1) Failed to recieve handshake from remote device (2) No session is currently active. Please try again after session established. (3) Received a bad transaction ID. Please try again. (4) We werent able to send the test request to the remote device. (5) We didnt receive any results from the remote device. |
| linkTestForceModulation |
Object ID: 1.3.6.1.4.1.161.19.3.1.2.1.9
Engineering use only. Link Test with: 0 = Normal Rate Adapt algorithm 1 = Force to max modultion - No Rate Adapt Algorithm |
| linkTestLUID |
Object ID: 1.3.6.1.4.1.161.19.3.1.2.1.1
LUID selection for Link Test. Valid range: 2-255 |
| linkTestMode |
Object ID: 1.3.6.1.4.1.161.19.3.1.2.1.5
Link Test Mode 0 = RF Link Test (traffic doesn't go through bridge, highest throughput) 1 = Link Test with Bridging 2 = Link Test with Bridging and MIR |
| linkTestNumPkt |
Object ID: 1.3.6.1.4.1.161.19.3.1.2.1.8
Number of packets to send. Valid range: 0-64 where 0 will flood the link for the duration of the test. |
| linkTestPktLength |
Object ID: 1.3.6.1.4.1.161.19.3.1.2.1.4
Packet length for Link Test. Valid range: 64-1714 bytes |
| linkTestSNRCalculation |
Object ID: 1.3.6.1.4.1.161.19.3.1.2.1.6
Enable or disable Signal to Noise Ratio (SNR) calculations during a Link Test. Enabling(1) will calulate SNR on all receiving packets. Due to load on CPU, will slightly degrade packet per second capabilities. Only applicable to GenII OFDM products and up. |
| linkTestStatus |
Object ID: 1.3.6.1.4.1.161.19.3.1.2.2.2
Status for Link Test. |
| linkTestWithDualPath |
Object ID: 1.3.6.1.4.1.161.19.3.1.2.1.7
Link Test with: 0 = Low Priority VC only 1 = High and Low Priority VCs |
| linkTimeOut |
Object ID: 1.3.6.1.4.1.161.19.3.1.4.1.27
Link time out. |
| maxDwnLinkIndex |
Object ID: 1.3.6.1.4.1.161.19.3.1.2.2.8
For link test results, the maximum possible downlink efficiency percentage (always 100%). |
| maxRange |
Object ID: 1.3.6.1.4.1.161.19.3.1.1.17
This attribute is deprecated. Please see radioMaxRange. |
| maxRegSMCount |
Object ID: 1.3.6.1.4.1.161.19.3.1.7.18
Maximum number of unique Subscriber Modules registered with this AP at once |
| maxSMTxPwr |
Object ID: 1.3.6.1.4.1.161.19.3.1.4.1.89
Returns whether SM is transmitting at its configured max power level. |
| maxUpLinkIndex |
Object ID: 1.3.6.1.4.1.161.19.3.1.2.2.15
For link test results, the maximum possible uplink efficiency percentage (always 100%). |
| multicastRetryCount |
Object ID: 1.3.6.1.4.1.161.19.3.1.1.219
Multicast Repeat Count : Range 0 - 2. For APs. |
| multicastVCDataRate |
Object ID: 1.3.6.1.4.1.161.19.3.1.1.217
The data rate that is used for the Multicast VC. 8X and MIMO-A are currently for engineering only. |
| ntpDomainNameAppend |
Object ID: 1.3.6.1.4.1.161.19.3.1.9.1
Select whether to append the configured management domain name to the configured trap names. For example, if dnsMgmtDomainName is set to 'example.com', ntpServer is set to 'ntp', and ntpDomainNameAppend is set to appendDomain, the ntpServer name used would be 'ntp.example.com'. |
| ntpLogSNMP |
Object ID: 1.3.6.1.4.1.161.19.3.1.7.33
NTP Log |
| ntpServer1 |
Object ID: 1.3.6.1.4.1.161.19.3.1.9.2
NTP Server 1 Address. Format is either an IP address or DNS name. |
| ntpServer2 |
Object ID: 1.3.6.1.4.1.161.19.3.1.9.3
NTP Server 2 Address. Format is either an IP address or DNS name. |
| ntpServer3 |
Object ID: 1.3.6.1.4.1.161.19.3.1.9.4
NTP Server 3 Address. Format is either an IP address or DNS name. |
| ntpServerIp |
Object ID: 1.3.6.1.4.1.161.19.3.1.1.34
Obsoleted. Configure with whispApsDNS.ntpServer1, whispApsDNS.ntpServer2, and whispApsDNS.ntpServer3. |
| numCtlSlots |
Object ID: 1.3.6.1.4.1.161.19.3.1.1.10
This OID is deprecated, please use numCtlSlotsHW. |
| numCtlSlotsHW |
Object ID: 1.3.6.1.4.1.161.19.3.1.1.42
This attribute is deprecated. Please see radioControlSlots. |
| numCtlSlotsReserveHigh |
Object ID: 1.3.6.1.4.1.161.19.3.1.1.11
Total number of High priority upstream control (contention) slots. |
| numCtrSlot |
Object ID: 1.3.6.1.4.1.161.19.3.1.7.12
Number of contention slots. |
| numCtrSlotHi |
Object ID: 1.3.6.1.4.1.161.19.3.1.7.13
High priority control slot. |
| numDAckSlots |
Object ID: 1.3.6.1.4.1.161.19.3.1.1.8
Total number of downstream ack slots. |
| numUAckSlots |
Object ID: 1.3.6.1.4.1.161.19.3.1.1.6
Total number of upstream ack slots. |
| ofdmSMRcvTargetLvl |
Object ID: 1.3.6.1.4.1.161.19.3.1.1.90
Desired SM Receive Level at AP (dBm, Range -40dBm to -80 dBm). As of release 12.1, on MIMO systems this is a combined power level value. |
| onlyAllowVer95OrAbove |
Object ID: 1.3.6.1.4.1.161.19.3.1.1.69
Only allow subscribers that are running version 9.5 or above. Any radio that has a version below 9.5 will not be allowed to register. |
| p7p8HiPriQ |
Object ID: 1.3.6.1.4.1.161.19.3.1.4.1.65
Hi Priority Queue statistics for P7 or P8 radios, if enabled. If not enabled, or not a P7 or P8, will return 0. |
| p7p8HiPriQEn |
Object ID: 1.3.6.1.4.1.161.19.3.1.4.1.64
Returns whether P7/P8 hi priority channel is enabled. On non-P7/P8 devices will return 0 always. |
| platformVer |
Object ID: 1.3.6.1.4.1.161.19.3.1.4.1.45
Platform Version. |
| pmp430InteropMode |
Object ID: 1.3.6.1.4.1.161.19.3.1.1.221
When the AP talks to a PMP 430 it can do so in either MIMO-A or SISO mode. 0 = MIMO-A 1 = SISO Only applies to PMP 450 AP at 5 GHz. By default in 13.2 the AP talks in MIMO-A to PMP 430 SISO SMs. Setting this to a 1 will enable SISO mode to PMP 430 SISO SMs, as it was in 13.1.3 and before. |
| privateIp |
Object ID: 1.3.6.1.4.1.161.19.3.1.1.26
Private IP. |
| productType |
Object ID: 1.3.6.1.4.1.161.19.3.1.4.1.90
Returns which type of product the SM is. PMP 450 APs only. |
| qinqEthType |
Object ID: 1.3.6.1.4.1.161.19.3.1.1.71
EtherType for QinQ (802.1ad) outer tag (S-Tag). 0x88a8 by default. |
| radioColorCode |
Object ID: 1.3.6.1.4.1.161.19.3.1.10.1.1.6
Color code. |
| radioControlSlots |
Object ID: 1.3.6.1.4.1.161.19.3.1.10.1.1.4
Total number of contention slots for HW Scheduling Point-to-Mulitpoint mode (Not applicable for PtoP radios). For PMP 450 the minimum is 1 control slot, others minimum is zero. Maximum contention slots is 15. |
| radioDownlinkPercent |
Object ID: 1.3.6.1.4.1.161.19.3.1.10.1.1.2
This is the percentage of frame data space allocated for downlink. |
| radioFreqCarrier |
Object ID: 1.3.6.1.4.1.161.19.3.1.10.1.1.1
RF Frequency. Please see the whispBoxRFPhysicalRadioFrequencies SNMP table for a list of available frequencies. 0: wired. |
| radioMaxRange |
Object ID: 1.3.6.1.4.1.161.19.3.1.10.1.1.3
Access point max range. |
| radioMode |
Object ID: 1.3.6.1.4.1.161.19.3.1.1.206
This OID is obsolete. |
| radioSlicingAp |
Object ID: 1.3.6.1.4.1.161.19.3.1.7.3
The variable is deprecated. |
| radioTransmitOutputPower |
Object ID: 1.3.6.1.4.1.161.19.3.1.10.1.1.5
Transmitter output power. |
| radioTxGainAp |
Object ID: 1.3.6.1.4.1.161.19.3.1.7.4
Radio transmit gain setting. |
| radiusAcctPort |
Object ID: 1.3.6.1.4.1.161.19.3.1.1.92
Port used to for RADIUS Accounting. Default is 1813. |
| radiusDefaultGateway |
Object ID: 1.3.6.1.4.1.161.19.3.1.4.1.79
This Attribute indicates the default gateway to be configured for the SM management interface. |
| radiusFramedIPAddress |
Object ID: 1.3.6.1.4.1.161.19.3.1.4.1.77
This Attribute indicates the IP address to be configured for the SM management interface. |
| radiusFramedIPNetmask |
Object ID: 1.3.6.1.4.1.161.19.3.1.4.1.78
This Attribute indicates the netmask to be configured for the SM management interface. |
| radiusPort |
Object ID: 1.3.6.1.4.1.161.19.3.1.1.91
Port used to connect to the RADIUS server. Default is 1812. |
| radiusReplyMsg |
Object ID: 1.3.6.1.4.1.161.19.3.1.4.1.75
The RADIUS Reply-Msg populated for the SM. This is only valid when using a backen AAA server. |
| regCount |
Object ID: 1.3.6.1.4.1.161.19.3.1.7.1
Number of registered SMs. |
| regFailESN |
Object ID: 1.3.6.1.4.1.161.19.3.1.8.1.2
The ESN that failed to register |
| regFailReasonText |
Object ID: 1.3.6.1.4.1.161.19.3.1.8.1.5
The text description of the failure. |
| regFailSeqNum |
Object ID: 1.3.6.1.4.1.161.19.3.1.8.1.4
The sequence when the register failure was given. |
| regFailTime |
Object ID: 1.3.6.1.4.1.161.19.3.1.8.1.3
The number of ticks that occurred when the ESN failed to register |
| regFailureCount |
Object ID: 1.3.6.1.4.1.161.19.3.1.7.32
The Total number or Registration Grant Failures. |
| regGrantReason |
Object ID: 1.3.6.1.4.1.161.19.3.1.8.1.1
The registration failure reason |
| regTrap |
Object ID: 1.3.6.1.4.1.161.19.3.1.1.28
Variable to enable/disable registration complete/lost traps. |
| regulatoryStatus |
Object ID: 1.3.6.1.4.1.161.19.3.1.7.21
The current status of the regulatory check on the AP. |
| remoteSpectrumAnalysisDuration |
Object ID: 1.3.6.1.4.1.161.19.3.1.1.56
Value in seconds for a remote spectrum analysis on an SM. Range is 10-1000 seconds. |
| remoteSpectrumAnalyzerLUID |
Object ID: 1.3.6.1.4.1.161.19.3.1.1.57
Get will return always return 0. Set will start Remote Spectrum Analyzer on specified LUID. *Warning* This will cause the SM to disconnect from the AP! You will lose the session for the specified duration! If general error was returned then the LUID does not have an active session, or the SM does not support Remote Spectrum Analysis. |
| remoteSpectrumAnalyzerScanBandwidth |
Object ID: 1.3.6.1.4.1.161.19.3.1.1.216
Scanning Bandwidth used for the Remote Spectrum Analyzer. Only available on PMP 450. |
| resetSesStats |
Object ID: 1.3.6.1.4.1.161.19.3.1.1.94
Resets the session stats if true. |
| rfFreqCaralt1 |
Object ID: 1.3.6.1.4.1.161.19.3.1.1.53
First DFS Alternate RF Frequency. (Only available for DFS radios) Used as a backup frequency when Radar is detected on DFS enabled Radios. The frequencies are: 5.4 radios:(5475,5485,5490 OFDM only),5495,5500,5505,5510,5515,5520,5525, 5530,5535,5540,5545,5550,5555,5560,5565,5570,5575,5580,5585,5590,5595, 5600,5605,5610,5615,5620,5625,5630,5635,5640,5645,5650,5655,5660,5665, 5670,5675,5680,5685,5690,5695,5700,5705,(5710,5715 OFDM Only). (5.7 Platform 10 (SAL) radios with non-connectorized antennas do not support DFS) 5.7 radios:5745,5750,5755,5760,5765,5770,5775,5780,5785,5790,5795,5800,5805. 5.7 radios with ISM enabled :5735,5740,5745,5750,5755,5760,5765,5770,5775, 5780,5785,5790,5795,5800,5805,5810,5815,5820,5825,5830,5835,5840. 0: None. |
| rfFreqCaralt2 |
Object ID: 1.3.6.1.4.1.161.19.3.1.1.54
Second DFS Alternate RF Frequency. (Only available for DFS radios) Used as a backup frequency when Radar is detected on DFS enabled Radios. The frequencies are: 5.4 radios:(5475,5485,5490 OFDM only),5495,5500,5505,5510,5515,5520,5525, 5530,5535,5540,5545,5550,5555,5560,5565,5570,5575,5580,5585,5590,5595, 5600,5605,5610,5615,5620,5625,5630,5635,5640,5645,5650,5655,5660,5665, 5670,5675,5680,5685,5690,5695,5700,5705,(5710,5715 OFDM Only). (5.7 Platform 10 (SAL) radios with non-connectorized antennas do not support DFS) 5.7 radios:5745,5750,5755,5760,5765,5770,5775,5780,5785,5790,5795,5800,5805. 5.7 radios with ISM enabled :5735,5740,5745,5750,5755,5760,5765,5770,5775, 5780,5785,5790,5795,5800,5805,5810,5815,5820,5825,5830,5835,5840. 0: None. |
| rfFreqCarrier |
Object ID: 1.3.6.1.4.1.161.19.3.1.1.2
The variable is deprecated. Please see radioFreqCarrier. |
| rfOLEnable |
Object ID: 1.3.6.1.4.1.161.19.3.1.1.97
Enable/Disable Throughput RF Overload Monitoring monitoring. |
| rfOLThreshold |
Object ID: 1.3.6.1.4.1.161.19.3.1.1.96
Percent of packet overload in the RF Downlink where SNMP is generated and sent to Network Manager. |
| rfOLTrap |
Object ID: 1.3.6.1.4.1.161.19.3.1.1.95
Enable/Disable SNMP Trap for when RF Overload exceeds configured Threshold level. |
| rfOutDiscardRate |
Object ID: 1.3.6.1.4.1.161.19.3.1.7.35
Percentage of OutDiscards on the RF link (RF Overload %) in the last minute. |
| rfPPPoEPADIForwarding |
Object ID: 1.3.6.1.4.1.161.19.3.1.1.210
Enables/disables forwarding of PPPoE PADI packets from AP to SM. |
| rfTelnetAccess |
Object ID: 1.3.6.1.4.1.161.19.3.1.1.207
Allows/prohibits uplink Telnet access (SM->AP). |
| scheduleWhitening |
Object ID: 1.3.6.1.4.1.161.19.3.1.1.55
1 = Schedule Whitening allowed. 0 = Schedule Whitening not allowed. This option is for FSK only |
| sectorID |
Object ID: 1.3.6.1.4.1.161.19.3.1.1.16
Advertise sector number for an AP. Not supported for PMP 450. |
| sesDownLinkLimit |
Object ID: 1.3.6.1.4.1.161.19.3.1.4.1.37
Down link limit. |
| sesDownLinkRate |
Object ID: 1.3.6.1.4.1.161.19.3.1.4.1.36
Down link rate. |
| sesHiDownCIR |
Object ID: 1.3.6.1.4.1.161.19.3.1.4.1.44
High priority down link CIR. |
| sesHiUpCIR |
Object ID: 1.3.6.1.4.1.161.19.3.1.4.1.43
High priority up link CIR. |
| sesLoDownCIR |
Object ID: 1.3.6.1.4.1.161.19.3.1.4.1.42
Low priority down link CIR. |
| sesLoUpCIR |
Object ID: 1.3.6.1.4.1.161.19.3.1.4.1.41
Low priority up link CIR. |
| sesUpLinkLimit |
Object ID: 1.3.6.1.4.1.161.19.3.1.4.1.39
Uplink limit. |
| sesUpLinkRate |
Object ID: 1.3.6.1.4.1.161.19.3.1.4.1.38
Uplink rate. |
| sessionCount |
Object ID: 1.3.6.1.4.1.161.19.3.1.4.1.29
How many times has this mac been in/out of session. |
| signalToNoiseRatioDownLinkHorizontal |
Object ID: 1.3.6.1.4.1.161.19.3.1.2.2.51
Estimated Signal to Noise Ratio in dB for the down link. For MIMO and forward. For MIMO this is the horizontal path. If operating in MIMO-A this will return 0. |
| signalToNoiseRatioDownLinkVertical |
Object ID: 1.3.6.1.4.1.161.19.3.1.2.2.33
Estimated Signal to Noise Ratio in dB for the down link. For Gen II OFDM and forward. For MIMO this is the vertical path. |
| signalToNoiseRatioHorizontal |
Object ID: 1.3.6.1.4.1.161.19.3.1.4.1.84
Estimate of the receive signal to noise ratio in dB. MIMO radios only. For MIMO this is the horizontal path. If operating in MIMO-A this will return 0. |
| signalToNoiseRatioUpLinkHorizontal |
Object ID: 1.3.6.1.4.1.161.19.3.1.2.2.52
Estimated Signal to Noise Ratio in dB for the up link. For Gen II OFDM and forward. For MIMO this is the horizontal path. If operating in MIMO-A this will return 0. |
| signalToNoiseRatioUpLinkVertical |
Object ID: 1.3.6.1.4.1.161.19.3.1.2.2.34
Estimated Signal to Noise Ratio in dB for the up link. For Gen II OFDM and forward. For MIMO this is the vertical path. |
| signalToNoiseRatioVertical |
Object ID: 1.3.6.1.4.1.161.19.3.1.4.1.74
Estimate of the receive signal to noise ratio in dB. For GenII OFDM and forward. For MIMO this is the vertical path. |
| smIsolation |
Object ID: 1.3.6.1.4.1.161.19.3.1.1.44
(0) -- Disable SM Isolation. (1) -- Enable SM Isolation by blocking SM destined packets. (2) -- Enable SM Isolation by forwarding SM packets upstream. |
| smSessionSeqNumMismatch |
Object ID: 1.3.6.1.4.1.161.19.3.1.4.1.47
The count of how many sequence number mismatch between the AP/BHM and the SM/BHS during the authentication challenge and authentication response messages. This status is only valid in a system where encryption is enabled and no authentication server is configured. |
| smSessionTmr |
Object ID: 1.3.6.1.4.1.161.19.3.1.4.1.46
SM session uptime |
| softwareBootVersion |
Object ID: 1.3.6.1.4.1.161.19.3.1.4.1.31
The software boot version of registered SM. |
| softwareVersion |
Object ID: 1.3.6.1.4.1.161.19.3.1.4.1.30
The software version of registered SM. |
| syslogDomainNameAppend |
Object ID: 1.3.6.1.4.1.161.19.3.1.1.101
This attribute is deprecated. Use syslogDomainNameAppend in whispBoxAttributesGroup |
| syslogServerAddr |
Object ID: 1.3.6.1.4.1.161.19.3.1.1.102
This attribute is deprecated. Use syslogServerAddr in whispBoxAttributesGroup |
| syslogServerPort |
Object ID: 1.3.6.1.4.1.161.19.3.1.1.103
This attribute is deprecated. Use syslogServerPort in whispBoxAttributesGroup |
| syslogXmitAP |
Object ID: 1.3.6.1.4.1.161.19.3.1.1.104
Enables/Disables transmission of Syslogs from AP/BHM |
| syslogXmitSMs |
Object ID: 1.3.6.1.4.1.161.19.3.1.1.105
Enables/Disables transmission of Syslogs from connected SMs/BHS. This can be over-ridden by the setting on individual SMs/ the BHS. |
| systemTime |
Object ID: 1.3.6.1.4.1.161.19.3.1.7.19
Displays the system time of the unit |
| testDuration |
Object ID: 1.3.6.1.4.1.161.19.3.1.2.2.4
Duration of link test. |
| testLUID |
Object ID: 1.3.6.1.4.1.161.19.3.1.2.2.1
LUID number of selected unit. |
| timeZone |
Object ID: 1.3.6.1.4.1.161.19.3.1.1.89
Set the timezone offset for the radio. This change takes affect dynamically. The available timezones are: 0 : (UTC) UTC - Coordinated Universal Time 1 : (UTC) GMT - Greenwich Mean Time 2 : (UTC) WET - Western European Time 3 : (UTC-12) BIT - Baker Island Time 4 : (UTC-11) SST - Samoa Standard Time 5 : (UTC-10) CKT - Cook Island Time 6 : (UTC-10) HAST - Hawaii-Aleutian Standard Time 7 : (UTC-10) HST - Hawaii Standard Time 8 : (UTC-10) TAHT - Tahiti Time 9 : (UTC-09:30) MIT - Marquesas Islands Time 10 : (UTC-09) AKST - Alaska Standard Time 11 : (UTC-09) GIT - Gambier Island Time 12 : (UTC-09) HADT - Hawaii-Aleutian Daylight Time 13 : (UTC-08) AKDT - Alaska Daylight Time 14 : (UTC-08) CIST - Clipperton Island Standard Time 15 : (UTC-08) PST - Pacific Standard Time (North America) 16 : (UTC-07) MST - Mountain Standard Time (North America) 17 : (UTC-07) PDT - Pacific Daylight Time (North America) 18 : (UTC-06) CST - Central Standard Time (North America) 19 : (UTC-06) EAST - Easter Island Standard Time 20 : (UTC-06) GALT - Galapagos Time 21 : (UTC-06) MDT - Mountain Daylight Time (North America) 22 : (UTC-05) CDT - Central Daylight Time (North America) 23 : (UTC-05) COT - Colombia Time 24 : (UTC-05) ECT - Ecuador Time 25 : (UTC-05) EST - Eastern Standard Time (North America) 26 : (UTC-04:30) VET - Venezuelan Standard Time 27 : (UTC-04) AST - Atlantic Standard Time 28 : (UTC-04) BOT - Bolivia Time 29 : (UTC-04) CLT - Chile Standard Time 30 : (UTC-04) COST - Colombia Summer Time 31 : (UTC-04) ECT - Eastern Caribbean Time (does not recognise DST) 32 : (UTC-04) EDT - Eastern Daylight Time (North America) 33 : (UTC-04) FKT - Falkland Islands Time 34 : (UTC-04) GYT - Guyana Time 35 : (UTC-03:30) NST - Newfoundland Standard Time 36 : (UTC-03:30) NT - Newfoundland Time 37 : (UTC-03) ADT - Atlantic Daylight Time 38 : (UTC-03) ART - Argentina Time 39 : (UTC-03) BRT - Brasilia Time 40 : (UTC-03) CLST - Chile Summer Time 41 : (UTC-03) FKST - Falkland Islands Summer Time 42 : (UTC-03) GFT - French Guiana Time 43 : (UTC-03) UYT - Uruguay Standard Time 44 : (UTC-02:30) NDT - Newfoundland Daylight Time 45 : (UTC-02) GST - South Georgia and the South Sandwich Islands 46 : (UTC-02) UYST - Uruguay Summer Time 47 : (UTC-01) AZOST - Azores Standard Time 48 : (UTC-01) CVT - Cape Verde Time 49 : (UTC+01) BST - British Summer Time (British Standard Time from Feb 1968 to Oct 1971) 50 : (UTC+01) CET - Central European Time 51 : (UTC+01) DFT - AIX specific equivalent of Central European Time 52 : (UTC+01) IST - Irish Summer Time 53 : (UTC+01) WAT - West Africa Time 54 : (UTC+01) WEDT - Western European Daylight Time 55 : (UTC+01) WEST - Western European Summer Time 56 : (UTC+02) CAT - Central Africa Time 57 : (UTC+02) CEDT - Central European Daylight Time 58 : (UTC+02) CEST - Central European Summer Time 59 : (UTC+02) EET - Eastern European Time 60 : (UTC+02) IST - Israel Standard Time 61 : (UTC+02) SAST - South African Standard Time 62 : (UTC+03) AST - Arab Standard Time (Kuwait, Riyadh) 63 : (UTC+03) AST - Arabic Standard Time (Baghdad) 64 : (UTC+03) EAT - East Africa Time 65 : (UTC+03) EEDT - Eastern European Daylight Time 66 : (UTC+03) EEST - Eastern European Summer Time 67 : (UTC+03) MSK - Moscow Standard Time 68 : (UTC+03:30) IRST - Iran Standard Time 69 : (UTC+04) AMT - Armenia Time 70 : (UTC+04) AST - Arabian Standard Time (Abu Dhabi, Muscat) 71 : (UTC+04) AZT - Azerbaijan Time 72 : (UTC+04) GET - Georgia Standard Time 73 : (UTC+04) MSD - Moscow Summer Time 74 : (UTC+04) MUT - Mauritius Time 75 : (UTC+04) RET - Reunion Time 76 : (UTC+04) SAMT - Samara Time 77 : (UTC+04) SCT - Seychelles Time 78 : (UTC+04:30) AFT - Afghanistan Time 79 : (UTC+05) AMST - Armenia Summer Time 80 : (UTC+05) HMT - Heard and McDonald Islands Time 81 : (UTC+05) PKT - Pakistan Standard Time 82 : (UTC+05) YEKT - Yekaterinburg Time 83 : (UTC+05:30) IST - Indian Standard Time 84 : (UTC+05:30) SLT - Sri Lanka Time 85 : (UTC+05:45) NPT - Nepal Time 86 : (UTC+06) BIOT - British Indian Ocean Time 87 : (UTC+06) BST - Bangladesh Standard Time 88 : (UTC+06) BTT - Bhutan Time 89 : (UTC+06) OMST - Omsk Time 90 : (UTC+06:30) CCT - Cocos Islands Time 91 : (UTC+06:30) MST - Myanmar Standard Time 92 : (UTC+07) CXT - Christmas Island Time 93 : (UTC+07) ICT - Indochina Time 94 : (UTC+07) KRAT - Krasnoyarsk Time 95 : (UTC+07) THA - Thailand Standard Time 96 : (UTC+08) ACT - ASEAN Common Time 97 : (UTC+08) AWST - Australian Western Standard Time 98 : (UTC+08) BDT - Brunei Time 99 : (UTC+08) CST - China Standard Time 100 : (UTC+08) HKT - Hong Kong Time 101 : (UTC+08) IRKT - Irkutsk Time 102 : (UTC+08) MST - Malaysian Standard Time 103 : (UTC+08) PST - Philippine Standard Time 104 : (UTC+08) SST - Singapore Standard Time 105 : (UTC+09) AWDT - Australian Western Daylight Time 106 : (UTC+09) JST - Japan Standard Time 107 : (UTC+09) KST - Korea Standard Time 108 : (UTC+09) YAKT - Yakutsk Time 109 : (UTC+09:30) ACST - Australian Central Standard Time 110 : (UTC+10) AEST - Australian Eastern Standard Time 111 : (UTC+10) ChST - Chamorro Standard Time 112 : (UTC+10) VLAT - Vladivostok Time 113 : (UTC+10:30) ACDT - Australian Central Daylight Time 114 : (UTC+10:30) LHST - Lord Howe Standard Time 115 : (UTC+11) AEDT - Australian Eastern Daylight Time 116 : (UTC+11) MAGT - Magadan Time 117 : (UTC+11) SBT - Solomon Islands Time 118 : (UTC+11:30) NFT - Norfolk Time[1] 119 : (UTC+12) FJT - Fiji Time 120 : (UTC+12) GILT - Gilbert Island Time 121 : (UTC+12) PETT - Kamchatka Time 122 : (UTC+12:45) CHAST - Chatham Standard Time 123 : (UTC+13) PHOT - Phoenix Island Time 124 : (UTC+14) LINT - Line Islands Time |
| tslBridging |
Object ID: 1.3.6.1.4.1.161.19.3.1.1.49
1 = We are performing Translation Bridging 0 = We are not. |
| txPwrLevel |
Object ID: 1.3.6.1.4.1.161.19.3.1.1.52
Deprecated, use 'transmitterOP' instead. |
| txSpreading |
Object ID: 1.3.6.1.4.1.161.19.3.1.1.29
Variable to enable/disable Transmit Frame Spreading. This option is for FSK only. |
| uAcksReservHigh |
Object ID: 1.3.6.1.4.1.161.19.3.1.1.7
Total number of upstream high priority ack slots |
| uGPSPower |
Object ID: 1.3.6.1.4.1.161.19.3.1.1.88
Enable or Disable power supply to Universal GPS module (UGPS capable APs only, when GPS_output_enable is NOT set). |
| uGPSPowerStatus |
Object ID: 1.3.6.1.4.1.161.19.3.1.7.34
Current UGPS Power Status (UGPS capable APs only). |
| untranslatedArp |
Object ID: 1.3.6.1.4.1.161.19.3.1.1.50
1 = We are sending untranslated ARP response. 0 = We are not. |
| upLinkEff |
Object ID: 1.3.6.1.4.1.161.19.3.1.2.2.12
Up link efficiency. |
| upLinkRate |
Object ID: 1.3.6.1.4.1.161.19.3.1.2.2.6
Up Link Rate. |
| upLnkAckSlot |
Object ID: 1.3.6.1.4.1.161.19.3.1.7.8
Uplink ack slots. |
| upLnkAckSlotHi |
Object ID: 1.3.6.1.4.1.161.19.3.1.7.9
Hige priority uplink ack slots. |
| upLnkDataRate |
Object ID: 1.3.6.1.4.1.161.19.3.1.1.12
Sustained uplink bandwidth cap. |
| upLnkLimit |
Object ID: 1.3.6.1.4.1.161.19.3.1.1.13
Burst uplink bandwidth cap. |
| upLnkMaxBurstDataRate |
Object ID: 1.3.6.1.4.1.161.19.3.1.1.208
Maximum burst uplink rate. |
| updateAppAddress |
Object ID: 1.3.6.1.4.1.161.19.3.1.1.37
Update Application Address. |
| vcQOverflow |
Object ID: 1.3.6.1.4.1.161.19.3.1.4.1.62
The number of packets dropped due to Queue overflow on VC. |
| vcQOverflowHiQ |
Object ID: 1.3.6.1.4.1.161.19.3.1.4.1.63
The number of packets dropped due to Queue overflow on High Priority VC, if enabled. |
| verifyGPSChecksum |
Object ID: 1.3.6.1.4.1.161.19.3.1.1.60
Enable/Disable verification of GPS message checksums. |
| vlanEnable |
Object ID: 1.3.6.1.4.1.161.19.3.1.1.39
To enable or disable VLAN. |
| whispApsRFConfigRadioEntry |
Object ID: 1.3.6.1.4.1.161.19.3.1.10.1.1
Radio configuration entry. |
| whispApsRFConfigRadios |
Object ID: 1.3.6.1.4.1.161.19.3.1.10.1
Radio configuration table. |
| whispFailedRegEntry |
Object ID: 1.3.6.1.4.1.161.19.3.1.8.1
List of Failed ESNs |
| whispFailedRegTable |
Object ID: 1.3.6.1.4.1.161.19.3.1.8
List of link test results |
| whispGPSStats |
Object ID: 1.3.6.1.4.1.161.19.3.1.3.1
This shows whether the AP is synchrinized to the GPS timer. |
| whispLinkEntry |
Object ID: 1.3.6.1.4.1.161.19.3.1.4.1
List of link test results |
| whispLinkTable |
Object ID: 1.3.6.1.4.1.161.19.3.1.4
List of link test results |
| whispRegStatus |
Object ID: 1.3.6.1.4.1.161.19.3.1.2.4
This shows the registration status of a link. |
| whispUsrAcctSvr1 |
Object ID: 1.3.6.1.4.1.161.19.3.1.1.82
Obsoleted. Use whispApsDNS.authServer1. |
| whispUsrAcctSvr2 |
Object ID: 1.3.6.1.4.1.161.19.3.1.1.83
Obsoleted. Use whispApsDNS.authServer2. |
| whispUsrAcctSvr3 |
Object ID: 1.3.6.1.4.1.161.19.3.1.1.84
Obsoleted. Use whispApsDNS.authServer3. |
| whispUsrAuthPhase1 |
Object ID: 1.3.6.1.4.1.161.19.3.1.1.85
Select method for User Authentication |
| whispUsrAuthSharedSecret1 |
Object ID: 1.3.6.1.4.1.161.19.3.1.1.79
Obsoleted. Use whispApsConfig.authSharedSecret1. |
| whispUsrAuthSharedSecret2 |
Object ID: 1.3.6.1.4.1.161.19.3.1.1.80
Obsoleted. Use whispApsConfig.authSharedSecret2. |
| whispUsrAuthSharedSecret3 |
Object ID: 1.3.6.1.4.1.161.19.3.1.1.81
Obsoleted. Use whispApsConfig.authSharedSecret3. |
| whispWebUseAuthServer |
Object ID: 1.3.6.1.4.1.161.19.3.1.1.86
Obsoleted. Use whispApsDNS.authServer[1-3]. |
| Notification Details |
Object ID: 1.3.6.1.4.1.161.19.3.1.5.4.3
Object ID: 1.3.6.1.4.1.161.19.3.1.5.4.1
Object ID: 1.3.6.1.4.1.161.19.3.1.5.4.2
Object ID: 1.3.6.1.4.1.161.19.3.1.5.5.1
Object ID: 1.3.6.1.4.1.161.19.3.1.5.1.4
Object ID: 1.3.6.1.4.1.161.19.3.1.5.2.1
Object ID: 1.3.6.1.4.1.161.19.3.1.5.2.2
Object ID: 1.3.6.1.4.1.161.19.3.1.5.3.1
Object ID: 1.3.6.1.4.1.161.19.3.1.5.3.2
Object ID: 1.3.6.1.4.1.161.19.3.1.5.1.1
Object ID: 1.3.6.1.4.1.161.19.3.1.5.1.3
Object ID: 1.3.6.1.4.1.161.19.3.1.5.1.2
| Object Details |
Object ID: 1.3.6.1.4.1.161.19.3.1.1.106
Object ID: 1.3.6.1.4.1.161.19.3.1.1.100
Object ID: 1.3.6.1.4.1.161.19.3.1.9.13
Object ID: 1.3.6.1.4.1.161.19.3.1.2.2.11
Object ID: 1.3.6.1.4.1.161.19.3.1.2.2.9
Object ID: 1.3.6.1.4.1.161.19.3.1.2.2.14
Object ID: 1.3.6.1.4.1.161.19.3.1.2.2.16
Object ID: 1.3.6.1.4.1.161.19.3.1.1.98
Object ID: 1.3.6.1.4.1.161.19.3.1.4.1.40
Object ID: 1.3.6.1.4.1.161.19.3.1.1.18
Object ID: 1.3.6.1.4.1.161.19.3.1.1.46
Object ID: 1.3.6.1.4.1.161.19.3.1.1.47
Object ID: 1.3.6.1.4.1.161.19.3.1.1.48
Object ID: 1.3.6.1.4.1.161.19.3.1.1.211
Object ID: 1.3.6.1.4.1.161.19.3.1.1.212
Object ID: 1.3.6.1.4.1.161.19.3.1.1.213
Object ID: 1.3.6.1.4.1.161.19.3.1.1.30
Object ID: 1.3.6.1.4.1.161.19.3.1.1.220
Object ID: 1.3.6.1.4.1.161.19.3.1.1.3
Object ID: 1.3.6.1.4.1.161.19.3.1.1.41
Object ID: 1.3.6.1.4.1.161.19.3.1.1.70
Object ID: 1.3.6.1.4.1.161.19.3.1.1.61
Object ID: 1.3.6.1.4.1.161.19.3.1.1.20
Object ID: 1.3.6.1.4.1.161.19.3.1.1.21
Object ID: 1.3.6.1.4.1.161.19.3.1.1.22
Object ID: 1.3.6.1.4.1.161.19.3.1.1.67
Object ID: 1.3.6.1.4.1.161.19.3.1.1.68
Object ID: 1.3.6.1.4.1.161.19.3.1.9.7
Object ID: 1.3.6.1.4.1.161.19.3.1.1.32
Object ID: 1.3.6.1.4.1.161.19.3.1.1.66
Object ID: 1.3.6.1.4.1.161.19.3.1.1.31
Object ID: 1.3.6.1.4.1.161.19.3.1.9.8
Object ID: 1.3.6.1.4.1.161.19.3.1.9.9
Object ID: 1.3.6.1.4.1.161.19.3.1.9.10
Object ID: 1.3.6.1.4.1.161.19.3.1.9.11
Object ID: 1.3.6.1.4.1.161.19.3.1.9.12
Object ID: 1.3.6.1.4.1.161.19.3.1.1.74
Object ID: 1.3.6.1.4.1.161.19.3.1.1.75
Object ID: 1.3.6.1.4.1.161.19.3.1.1.76
Object ID: 1.3.6.1.4.1.161.19.3.1.3.18
Object ID: 1.3.6.1.4.1.161.19.3.1.7.36
Object ID: 1.3.6.1.4.1.161.19.3.1.4.1.76
Object ID: 1.3.6.1.4.1.161.19.3.1.4.1.34
Object ID: 1.3.6.1.4.1.161.19.3.1.1.215
Object ID: 1.3.6.1.4.1.161.19.3.1.1.19
Object ID: 1.3.6.1.4.1.161.19.3.1.1.58
Object ID: 1.3.6.1.4.1.161.19.3.1.2.2.43
Object ID: 1.3.6.1.4.1.161.19.3.1.2.2.25
Object ID: 1.3.6.1.4.1.161.19.3.1.2.2.47
Object ID: 1.3.6.1.4.1.161.19.3.1.2.2.29
Object ID: 1.3.6.1.4.1.161.19.3.1.2.2.44
Object ID: 1.3.6.1.4.1.161.19.3.1.2.2.26
Object ID: 1.3.6.1.4.1.161.19.3.1.2.2.48
Object ID: 1.3.6.1.4.1.161.19.3.1.2.2.30
Object ID: 1.3.6.1.4.1.161.19.3.1.2.2.45
Object ID: 1.3.6.1.4.1.161.19.3.1.2.2.27
Object ID: 1.3.6.1.4.1.161.19.3.1.2.2.49
Object ID: 1.3.6.1.4.1.161.19.3.1.2.2.31
Object ID: 1.3.6.1.4.1.161.19.3.1.2.2.46
Object ID: 1.3.6.1.4.1.161.19.3.1.2.2.28
Object ID: 1.3.6.1.4.1.161.19.3.1.2.2.50
Object ID: 1.3.6.1.4.1.161.19.3.1.2.2.32
Object ID: 1.3.6.1.4.1.161.19.3.1.1.214
Object ID: 1.3.6.1.4.1.161.19.3.1.1.35
Object ID: 1.3.6.1.4.1.161.19.3.1.11.1
Object ID: 1.3.6.1.4.1.161.19.3.1.1.65
Object ID: 1.3.6.1.4.1.161.19.3.1.1.64
Object ID: 1.3.6.1.4.1.161.19.3.1.1.40
Object ID: 1.3.6.1.4.1.161.19.3.1.7.37
Object ID: 1.3.6.1.4.1.161.19.3.1.1.9
Object ID: 1.3.6.1.4.1.161.19.3.1.7.5
Object ID: 1.3.6.1.4.1.161.19.3.1.7.6
Object ID: 1.3.6.1.4.1.161.19.3.1.7.7
Object ID: 1.3.6.1.4.1.161.19.3.1.4.1.48
Object ID: 1.3.6.1.4.1.161.19.3.1.4.1.50
Object ID: 1.3.6.1.4.1.161.19.3.1.1.25
Object ID: 1.3.6.1.4.1.161.19.3.1.1.38
Object ID: 1.3.6.1.4.1.161.19.3.1.7.14
Object ID: 1.3.6.1.4.1.161.19.3.1.7.16
Object ID: 1.3.6.1.4.1.161.19.3.1.7.17
Object ID: 1.3.6.1.4.1.161.19.3.1.7.15
Object ID: 1.3.6.1.4.1.161.19.3.1.1.62
Object ID: 1.3.6.1.4.1.161.19.3.1.1.63
Object ID: 1.3.6.1.4.1.161.19.3.1.7.31
Object ID: 1.3.6.1.4.1.161.19.3.1.7.29
Object ID: 1.3.6.1.4.1.161.19.3.1.7.30
Object ID: 1.3.6.1.4.1.161.19.3.1.7.24
Object ID: 1.3.6.1.4.1.161.19.3.1.7.22
Object ID: 1.3.6.1.4.1.161.19.3.1.7.23
Object ID: 1.3.6.1.4.1.161.19.3.1.7.27
Object ID: 1.3.6.1.4.1.161.19.3.1.7.25
Object ID: 1.3.6.1.4.1.161.19.3.1.7.26
Object ID: 1.3.6.1.4.1.161.19.3.1.7.28
Object ID: 1.3.6.1.4.1.161.19.3.1.9.5
Object ID: 1.3.6.1.4.1.161.19.3.1.9.6
Object ID: 1.3.6.1.4.1.161.19.3.1.1.43
Object ID: 1.3.6.1.4.1.161.19.3.1.1.59
Object ID: 1.3.6.1.4.1.161.19.3.1.1.218
Object ID: 1.3.6.1.4.1.161.19.3.1.2.2.7
Object ID: 1.3.6.1.4.1.161.19.3.1.2.2.5
Object ID: 1.3.6.1.4.1.161.19.3.1.1.87
Object ID: 1.3.6.1.4.1.161.19.3.1.7.10
Object ID: 1.3.6.1.4.1.161.19.3.1.7.11
Object ID: 1.3.6.1.4.1.161.19.3.1.1.4
Object ID: 1.3.6.1.4.1.161.19.3.1.1.14
Object ID: 1.3.6.1.4.1.161.19.3.1.1.15
Object ID: 1.3.6.1.4.1.161.19.3.1.1.209
Object ID: 1.3.6.1.4.1.161.19.3.1.1.99
Object ID: 1.3.6.1.4.1.161.19.3.1.1.36
Object ID: 1.3.6.1.4.1.161.19.3.1.1.33
Object ID: 1.3.6.1.4.1.161.19.3.1.2.2.10
Object ID: 1.3.6.1.4.1.161.19.3.1.2.2.13
Object ID: 1.3.6.1.4.1.161.19.3.1.4.1.32
Object ID: 1.3.6.1.4.1.161.19.3.1.2.2.35
Object ID: 1.3.6.1.4.1.161.19.3.1.2.2.17
Object ID: 1.3.6.1.4.1.161.19.3.1.2.2.39
Object ID: 1.3.6.1.4.1.161.19.3.1.2.2.21
Object ID: 1.3.6.1.4.1.161.19.3.1.2.2.36
Object ID: 1.3.6.1.4.1.161.19.3.1.2.2.18
Object ID: 1.3.6.1.4.1.161.19.3.1.2.2.40
Object ID: 1.3.6.1.4.1.161.19.3.1.2.2.22
Object ID: 1.3.6.1.4.1.161.19.3.1.2.2.37
Object ID: 1.3.6.1.4.1.161.19.3.1.2.2.19
Object ID: 1.3.6.1.4.1.161.19.3.1.2.2.41
Object ID: 1.3.6.1.4.1.161.19.3.1.2.2.23
Object ID: 1.3.6.1.4.1.161.19.3.1.2.2.38
Object ID: 1.3.6.1.4.1.161.19.3.1.2.2.20
Object ID: 1.3.6.1.4.1.161.19.3.1.2.2.42
Object ID: 1.3.6.1.4.1.161.19.3.1.2.2.24
Object ID: 1.3.6.1.4.1.161.19.3.1.1.73
Object ID: 1.3.6.1.4.1.161.19.3.1.1.72
Object ID: 1.3.6.1.4.1.161.19.3.1.3.10
Object ID: 1.3.6.1.4.1.161.19.3.1.3.6
Object ID: 1.3.6.1.4.1.161.19.3.1.3.17
Object ID: 1.3.6.1.4.1.161.19.3.1.3.9
Object ID: 1.3.6.1.4.1.161.19.3.1.1.1
Object ID: 1.3.6.1.4.1.161.19.3.1.3.13
Object ID: 1.3.6.1.4.1.161.19.3.1.3.11
Object ID: 1.3.6.1.4.1.161.19.3.1.3.12
Object ID: 1.3.6.1.4.1.161.19.3.1.1.107
Object ID: 1.3.6.1.4.1.161.19.3.1.3.15
Object ID: 1.3.6.1.4.1.161.19.3.1.3.16
Object ID: 1.3.6.1.4.1.161.19.3.1.3.14
Object ID: 1.3.6.1.4.1.161.19.3.1.3.7
Object ID: 1.3.6.1.4.1.161.19.3.1.3.19
Object ID: 1.3.6.1.4.1.161.19.3.1.3.8
Object ID: 1.3.6.1.4.1.161.19.3.1.3.20
Object ID: 1.3.6.1.4.1.161.19.3.1.7.2
Object ID: 1.3.6.1.4.1.161.19.3.1.3.2
Object ID: 1.3.6.1.4.1.161.19.3.1.3.3
Object ID: 1.3.6.1.4.1.161.19.3.1.3.5
Object ID: 1.3.6.1.4.1.161.19.3.1.3.4
Object ID: 1.3.6.1.4.1.161.19.3.1.1.27
Object ID: 1.3.6.1.4.1.161.19.3.1.4.1.49
Object ID: 1.3.6.1.4.1.161.19.3.1.1.5
Object ID: 1.3.6.1.4.1.161.19.3.1.1.45
Object ID: 1.3.6.1.4.1.161.19.3.1.1.23
Object ID: 1.3.6.1.4.1.161.19.3.1.1.24
Object ID: 1.3.6.1.4.1.161.19.3.1.7.20
Object ID: 1.3.6.1.4.1.161.19.3.1.4.1.35
Object ID: 1.3.6.1.4.1.161.19.3.1.1.93
Object ID: 1.3.6.1.4.1.161.19.3.1.1.51
Object ID: 1.3.6.1.4.1.161.19.3.1.4.1.92
Object ID: 1.3.6.1.4.1.161.19.3.1.4.1.91
Object ID: 1.3.6.1.4.1.161.19.3.1.4.1.24
Object ID: 1.3.6.1.4.1.161.19.3.1.4.1.66
Object ID: 1.3.6.1.4.1.161.19.3.1.4.1.22
Object ID: 1.3.6.1.4.1.161.19.3.1.4.1.2
Object ID: 1.3.6.1.4.1.161.19.3.1.4.1.20
Object ID: 1.3.6.1.4.1.161.19.3.1.4.1.80
Object ID: 1.3.6.1.4.1.161.19.3.1.4.1.70
Object ID: 1.3.6.1.4.1.161.19.3.1.4.1.81
Object ID: 1.3.6.1.4.1.161.19.3.1.4.1.71
Object ID: 1.3.6.1.4.1.161.19.3.1.4.1.82
Object ID: 1.3.6.1.4.1.161.19.3.1.4.1.72
Object ID: 1.3.6.1.4.1.161.19.3.1.4.1.83
Object ID: 1.3.6.1.4.1.161.19.3.1.4.1.73
Object ID: 1.3.6.1.4.1.161.19.3.1.4.1.10
Object ID: 1.3.6.1.4.1.161.19.3.1.4.1.54
Object ID: 1.3.6.1.4.1.161.19.3.1.4.1.11
Object ID: 1.3.6.1.4.1.161.19.3.1.4.1.55
Object ID: 1.3.6.1.4.1.161.19.3.1.4.1.9
Object ID: 1.3.6.1.4.1.161.19.3.1.4.1.53
Object ID: 1.3.6.1.4.1.161.19.3.1.4.1.7
Object ID: 1.3.6.1.4.1.161.19.3.1.4.1.51
Object ID: 1.3.6.1.4.1.161.19.3.1.4.1.8
Object ID: 1.3.6.1.4.1.161.19.3.1.4.1.52
Object ID: 1.3.6.1.4.1.161.19.3.1.4.1.12
Object ID: 1.3.6.1.4.1.161.19.3.1.4.1.56
Object ID: 1.3.6.1.4.1.161.19.3.1.4.1.1
Object ID: 1.3.6.1.4.1.161.19.3.1.4.1.23
Object ID: 1.3.6.1.4.1.161.19.3.1.4.1.28
Object ID: 1.3.6.1.4.1.161.19.3.1.4.1.69
Object ID: 1.3.6.1.4.1.161.19.3.1.4.1.4
Object ID: 1.3.6.1.4.1.161.19.3.1.4.1.6
Object ID: 1.3.6.1.4.1.161.19.3.1.4.1.16
Object ID: 1.3.6.1.4.1.161.19.3.1.4.1.60
Object ID: 1.3.6.1.4.1.161.19.3.1.4.1.17
Object ID: 1.3.6.1.4.1.161.19.3.1.4.1.61
Object ID: 1.3.6.1.4.1.161.19.3.1.4.1.15
Object ID: 1.3.6.1.4.1.161.19.3.1.4.1.59
Object ID: 1.3.6.1.4.1.161.19.3.1.4.1.13
Object ID: 1.3.6.1.4.1.161.19.3.1.4.1.57
Object ID: 1.3.6.1.4.1.161.19.3.1.4.1.18
Object ID: 1.3.6.1.4.1.161.19.3.1.4.1.14
Object ID: 1.3.6.1.4.1.161.19.3.1.4.1.58
Object ID: 1.3.6.1.4.1.161.19.3.1.4.1.3
Object ID: 1.3.6.1.4.1.161.19.3.1.4.1.67
Object ID: 1.3.6.1.4.1.161.19.3.1.4.1.21
Object ID: 1.3.6.1.4.1.161.19.3.1.4.1.87
Object ID: 1.3.6.1.4.1.161.19.3.1.4.1.88
Object ID: 1.3.6.1.4.1.161.19.3.1.4.1.26
Object ID: 1.3.6.1.4.1.161.19.3.1.4.1.25
Object ID: 1.3.6.1.4.1.161.19.3.1.4.1.19
Object ID: 1.3.6.1.4.1.161.19.3.1.4.1.86
Object ID: 1.3.6.1.4.1.161.19.3.1.4.1.33
Object ID: 1.3.6.1.4.1.161.19.3.1.4.1.5
Object ID: 1.3.6.1.4.1.161.19.3.1.2.1.3
Object ID: 1.3.6.1.4.1.161.19.3.1.2.1.10
Object ID: 1.3.6.1.4.1.161.19.3.1.2.1.2
Object ID: 1.3.6.1.4.1.161.19.3.1.2.2.3
Object ID: 1.3.6.1.4.1.161.19.3.1.2.1.9
Object ID: 1.3.6.1.4.1.161.19.3.1.2.1.1
Object ID: 1.3.6.1.4.1.161.19.3.1.2.1.5
Object ID: 1.3.6.1.4.1.161.19.3.1.2.1.8
Object ID: 1.3.6.1.4.1.161.19.3.1.2.1.4
Object ID: 1.3.6.1.4.1.161.19.3.1.2.1.6
Object ID: 1.3.6.1.4.1.161.19.3.1.2.2.2
Object ID: 1.3.6.1.4.1.161.19.3.1.2.1.7
Object ID: 1.3.6.1.4.1.161.19.3.1.4.1.27
Object ID: 1.3.6.1.4.1.161.19.3.1.2.2.8
Object ID: 1.3.6.1.4.1.161.19.3.1.1.17
Object ID: 1.3.6.1.4.1.161.19.3.1.7.18
Object ID: 1.3.6.1.4.1.161.19.3.1.4.1.89
Object ID: 1.3.6.1.4.1.161.19.3.1.2.2.15
Object ID: 1.3.6.1.4.1.161.19.3.1.1.219
Object ID: 1.3.6.1.4.1.161.19.3.1.1.217
Object ID: 1.3.6.1.4.1.161.19.3.1.9.1
Object ID: 1.3.6.1.4.1.161.19.3.1.7.33
Object ID: 1.3.6.1.4.1.161.19.3.1.9.2
Object ID: 1.3.6.1.4.1.161.19.3.1.9.3
Object ID: 1.3.6.1.4.1.161.19.3.1.9.4
Object ID: 1.3.6.1.4.1.161.19.3.1.1.34
Object ID: 1.3.6.1.4.1.161.19.3.1.1.10
Object ID: 1.3.6.1.4.1.161.19.3.1.1.42
Object ID: 1.3.6.1.4.1.161.19.3.1.1.11
Object ID: 1.3.6.1.4.1.161.19.3.1.7.12
Object ID: 1.3.6.1.4.1.161.19.3.1.7.13
Object ID: 1.3.6.1.4.1.161.19.3.1.1.8
Object ID: 1.3.6.1.4.1.161.19.3.1.1.6
Object ID: 1.3.6.1.4.1.161.19.3.1.1.90
Object ID: 1.3.6.1.4.1.161.19.3.1.1.69
Object ID: 1.3.6.1.4.1.161.19.3.1.4.1.65
Object ID: 1.3.6.1.4.1.161.19.3.1.4.1.64
Object ID: 1.3.6.1.4.1.161.19.3.1.4.1.45
Object ID: 1.3.6.1.4.1.161.19.3.1.1.221
Object ID: 1.3.6.1.4.1.161.19.3.1.1.26
Object ID: 1.3.6.1.4.1.161.19.3.1.4.1.90
Object ID: 1.3.6.1.4.1.161.19.3.1.1.71
Object ID: 1.3.6.1.4.1.161.19.3.1.10.1.1.6
Object ID: 1.3.6.1.4.1.161.19.3.1.10.1.1.4
Object ID: 1.3.6.1.4.1.161.19.3.1.10.1.1.2
Object ID: 1.3.6.1.4.1.161.19.3.1.10.1.1.1
Object ID: 1.3.6.1.4.1.161.19.3.1.10.1.1.3
Object ID: 1.3.6.1.4.1.161.19.3.1.1.206
Object ID: 1.3.6.1.4.1.161.19.3.1.7.3
Object ID: 1.3.6.1.4.1.161.19.3.1.10.1.1.5
Object ID: 1.3.6.1.4.1.161.19.3.1.7.4
Object ID: 1.3.6.1.4.1.161.19.3.1.1.92
Object ID: 1.3.6.1.4.1.161.19.3.1.4.1.79
Object ID: 1.3.6.1.4.1.161.19.3.1.4.1.77
Object ID: 1.3.6.1.4.1.161.19.3.1.4.1.78
Object ID: 1.3.6.1.4.1.161.19.3.1.1.91
Object ID: 1.3.6.1.4.1.161.19.3.1.4.1.75
Object ID: 1.3.6.1.4.1.161.19.3.1.7.1
Object ID: 1.3.6.1.4.1.161.19.3.1.8.1.2
Object ID: 1.3.6.1.4.1.161.19.3.1.8.1.5
Object ID: 1.3.6.1.4.1.161.19.3.1.8.1.4
Object ID: 1.3.6.1.4.1.161.19.3.1.8.1.3
Object ID: 1.3.6.1.4.1.161.19.3.1.7.32
Object ID: 1.3.6.1.4.1.161.19.3.1.8.1.1
Object ID: 1.3.6.1.4.1.161.19.3.1.1.28
Object ID: 1.3.6.1.4.1.161.19.3.1.7.21
Object ID: 1.3.6.1.4.1.161.19.3.1.1.56
Object ID: 1.3.6.1.4.1.161.19.3.1.1.57
Object ID: 1.3.6.1.4.1.161.19.3.1.1.216
Object ID: 1.3.6.1.4.1.161.19.3.1.1.94
Object ID: 1.3.6.1.4.1.161.19.3.1.1.53
Object ID: 1.3.6.1.4.1.161.19.3.1.1.54
Object ID: 1.3.6.1.4.1.161.19.3.1.1.2
Object ID: 1.3.6.1.4.1.161.19.3.1.1.97
Object ID: 1.3.6.1.4.1.161.19.3.1.1.96
Object ID: 1.3.6.1.4.1.161.19.3.1.1.95
Object ID: 1.3.6.1.4.1.161.19.3.1.7.35
Object ID: 1.3.6.1.4.1.161.19.3.1.1.210
Object ID: 1.3.6.1.4.1.161.19.3.1.1.207
Object ID: 1.3.6.1.4.1.161.19.3.1.1.55
Object ID: 1.3.6.1.4.1.161.19.3.1.1.16
Object ID: 1.3.6.1.4.1.161.19.3.1.4.1.37
Object ID: 1.3.6.1.4.1.161.19.3.1.4.1.36
Object ID: 1.3.6.1.4.1.161.19.3.1.4.1.44
Object ID: 1.3.6.1.4.1.161.19.3.1.4.1.43
Object ID: 1.3.6.1.4.1.161.19.3.1.4.1.42
Object ID: 1.3.6.1.4.1.161.19.3.1.4.1.41
Object ID: 1.3.6.1.4.1.161.19.3.1.4.1.39
Object ID: 1.3.6.1.4.1.161.19.3.1.4.1.38
Object ID: 1.3.6.1.4.1.161.19.3.1.4.1.29
Object ID: 1.3.6.1.4.1.161.19.3.1.2.2.51
Object ID: 1.3.6.1.4.1.161.19.3.1.2.2.33
Object ID: 1.3.6.1.4.1.161.19.3.1.4.1.84
Object ID: 1.3.6.1.4.1.161.19.3.1.2.2.52
Object ID: 1.3.6.1.4.1.161.19.3.1.2.2.34
Object ID: 1.3.6.1.4.1.161.19.3.1.4.1.74
Object ID: 1.3.6.1.4.1.161.19.3.1.1.44
Object ID: 1.3.6.1.4.1.161.19.3.1.4.1.47
Object ID: 1.3.6.1.4.1.161.19.3.1.4.1.46
Object ID: 1.3.6.1.4.1.161.19.3.1.4.1.31
Object ID: 1.3.6.1.4.1.161.19.3.1.4.1.30
Object ID: 1.3.6.1.4.1.161.19.3.1.1.101
Object ID: 1.3.6.1.4.1.161.19.3.1.1.102
Object ID: 1.3.6.1.4.1.161.19.3.1.1.103
Object ID: 1.3.6.1.4.1.161.19.3.1.1.104
Object ID: 1.3.6.1.4.1.161.19.3.1.1.105
Object ID: 1.3.6.1.4.1.161.19.3.1.7.19
Object ID: 1.3.6.1.4.1.161.19.3.1.2.2.4
Object ID: 1.3.6.1.4.1.161.19.3.1.2.2.1
Object ID: 1.3.6.1.4.1.161.19.3.1.1.89
Object ID: 1.3.6.1.4.1.161.19.3.1.1.49
Object ID: 1.3.6.1.4.1.161.19.3.1.1.52
Object ID: 1.3.6.1.4.1.161.19.3.1.1.29
Object ID: 1.3.6.1.4.1.161.19.3.1.1.7
Object ID: 1.3.6.1.4.1.161.19.3.1.1.88
Object ID: 1.3.6.1.4.1.161.19.3.1.7.34
Object ID: 1.3.6.1.4.1.161.19.3.1.1.50
Object ID: 1.3.6.1.4.1.161.19.3.1.2.2.12
Object ID: 1.3.6.1.4.1.161.19.3.1.2.2.6
Object ID: 1.3.6.1.4.1.161.19.3.1.7.8
Object ID: 1.3.6.1.4.1.161.19.3.1.7.9
Object ID: 1.3.6.1.4.1.161.19.3.1.1.12
Object ID: 1.3.6.1.4.1.161.19.3.1.1.13
Object ID: 1.3.6.1.4.1.161.19.3.1.1.208
Object ID: 1.3.6.1.4.1.161.19.3.1.1.37
Object ID: 1.3.6.1.4.1.161.19.3.1.4.1.62
Object ID: 1.3.6.1.4.1.161.19.3.1.4.1.63
Object ID: 1.3.6.1.4.1.161.19.3.1.1.60
Object ID: 1.3.6.1.4.1.161.19.3.1.1.39
Object ID: 1.3.6.1.4.1.161.19.3.1.10.1.1
Object ID: 1.3.6.1.4.1.161.19.3.1.10.1
Object ID: 1.3.6.1.4.1.161.19.3.1.8.1
Object ID: 1.3.6.1.4.1.161.19.3.1.8
Object ID: 1.3.6.1.4.1.161.19.3.1.3.1
Object ID: 1.3.6.1.4.1.161.19.3.1.4.1
Object ID: 1.3.6.1.4.1.161.19.3.1.4
Object ID: 1.3.6.1.4.1.161.19.3.1.2.4
Object ID: 1.3.6.1.4.1.161.19.3.1.1.82
Object ID: 1.3.6.1.4.1.161.19.3.1.1.83
Object ID: 1.3.6.1.4.1.161.19.3.1.1.84
Object ID: 1.3.6.1.4.1.161.19.3.1.1.85
Object ID: 1.3.6.1.4.1.161.19.3.1.1.79
Object ID: 1.3.6.1.4.1.161.19.3.1.1.80
Object ID: 1.3.6.1.4.1.161.19.3.1.1.81
Object ID: 1.3.6.1.4.1.161.19.3.1.1.86