MIB File
PMP Subscriber Module

Module Information:

File:	WHISP-SM-MIB
Description:	This module contains MIB definitions for Subscriber Modem.
Organization:	Cambium Networks
Version:	Software Release v13.x
Contact Info:	Canopy Technical Support email: support@cambiumnetworks.com

availableSpectrumAnalysis

Object ID: 1.3.6.1.4.1.161.19.3.2.4.2.2

Syntax: Sequence (Structure)

availableSpectrumAnalysis

whispBoxEsn

Access: SNMP Notification
Status: current

Spectrum analysis is complete, SM is re-registered with AP and results are available.
physAddress - MAC address of the SM

enterSpectrumAnalysis

Object ID: 1.3.6.1.4.1.161.19.3.2.4.2.1

Syntax: Sequence (Structure)

enterSpectrumAnalysis

whispBoxEsn

Access: SNMP Notification
Status: current

Entering spectrum analysis.
physAddress - MAC address of the SM

smNatRFPubDHCPClientEvent

Object ID: 1.3.6.1.4.1.161.19.3.2.4.3.2

Syntax: Sequence (Structure)

smNatRFPubDHCPClientEvent

dhcpRfPublicIp

whispBoxEsn

Access: SNMP Notification
Status: current

NAT RF Public DHCP Client has received a new address via DHCP.

smNatWanDHCPClientEvent

Object ID: 1.3.6.1.4.1.161.19.3.2.4.3.1

Syntax: Sequence (Structure)

smNatWanDHCPClientEvent

dhcpCip

whispBoxEsn

Access: SNMP Notification
Status: current

NAT WAN DHCP Client has received a new address via DHCP.

whispRadarDetected

Object ID: 1.3.6.1.4.1.161.19.3.2.4.1.1

Syntax: Sequence (Structure)

whispRadarDetected

dfsStatus

whispBoxEsn

Access: SNMP Notification
Status: current

Radar detected transmit stopped.

whispRadarEnd

Object ID: 1.3.6.1.4.1.161.19.3.2.4.1.2

Syntax: Sequence (Structure)

whispRadarEnd

dfsStatus

whispBoxEsn

Access: SNMP Notification
Status: current

Radar ended back to normal transmit.

action

Object ID: 1.3.6.1.4.1.161.19.3.2.7.1.1.3

Syntax: INTEGER
Constraints:

0: noop

1: delete

Access: read-write
Status: current

0: No Operation 1: Delete Certificate

activeRegion

Object ID: 1.3.6.1.4.1.161.19.3.2.2.24

Syntax: OCTET STRING
Constraints: SIZE (0..255)
Access: read-only
Status: current

The active region of the radio.

adaptRate

Object ID: 1.3.6.1.4.1.161.19.3.2.2.20

Syntax: OCTET STRING
Constraints: SIZE (0..255)
Access: read-only
Status: current

VC adapt rate.

adaptRateHighPri

Object ID: 1.3.6.1.4.1.161.19.3.2.2.129

Syntax: INTEGER
Constraints:

-1: noHighPriorityChannel

0: noSession

1: rate1X

2: rate2X

3: rete3X

4: rate4X

6: rate6X

8: rate8X

Access: read-only
Status: current

The current transmitting rate of the high priority VC.
-1 : High Priority Channel not configured
0 : SM is not in session
1 : 1X QPSK SISO
2 : 2X 16-QAM SISO or QPSK MIMO
3 : 3X 64-QAM SISO
4 : 4X 256-QAM SISO or 16-QAM MIMO
6 : 6X 64-QAM MIMO
8 : 8X 256-QAM MIMO

adaptRateLowPri

Object ID: 1.3.6.1.4.1.161.19.3.2.2.128

Syntax: INTEGER
Constraints:

0: noSession

1: rate1X

2: rate2X

3: rete3X

4: rate4X

6: rate6X

8: rate8X

Access: read-only
Status: current

The current transmitting rate of the low priority VC.
0 : SM is not in session
1 : 1X QPSK SISO
2 : 2X 16-QAM SISO or QPSK MIMO
3 : 3X 64-QAM SISO
4 : 4X 256-QAM SISO or 16-QAM MIMO
6 : 6X 64-QAM MIMO
8 : 8X 256-QAM MIMO

airDelay

Object ID: 1.3.6.1.4.1.161.19.3.2.2.4

Syntax: Gauge
Constraints: 0..4294967295
Access: read-only
Status: current

Round trip delay in bits.

airDelayns

Object ID: 1.3.6.1.4.1.161.19.3.2.2.64

Syntax: Gauge
Constraints: 0..4294967295
Access: read-only
Status: current

Round trip delay in nanoseconds.

allIpv4Filter

Object ID: 1.3.6.1.4.1.161.19.3.2.1.116

Syntax: INTEGER
Constraints:

0: filterOff

1: filterOn

Access: read-write
Status: obsolete

To set all IPv4 packet filter when NAT
is disabled. Enabling this will automatically enable all of the known IP filters (SMB, SNMP, Bootp,
IPv4 Mcast, User Defined Ports, and All Other IPv4).
Obsolete - Use corresponding OID in whipsBoxConfig MIB.

allOtherIpFilter

Object ID: 1.3.6.1.4.1.161.19.3.2.1.39

Syntax: INTEGER
Constraints:

0: filterOff

1: filterOn

Access: read-write
Status: obsolete

To set all other IPv4 packet filter when NAT
is disabled.
Obsolete - Use corresponding OID in whipsBoxConfig MIB.

allOthersFilter

Object ID: 1.3.6.1.4.1.161.19.3.2.1.42

Syntax: INTEGER
Constraints:

0: filterOff

1: filterOn

Access: read-write
Status: obsolete

To set all other packet filter when NAT is disabled.
Obsolete - Use corresponding OID in whipsBoxConfig MIB.

allowedIPAccess1

Object ID: 1.3.6.1.4.1.161.19.3.2.1.69

Syntax: STRING
Constraints: SIZE (4)
Access: read-write
Status: current

Allow access to SM Management from this IP.
0 is default setting to allow from all IPs.

allowedIPAccess2

Object ID: 1.3.6.1.4.1.161.19.3.2.1.70

Syntax: STRING
Constraints: SIZE (4)
Access: read-write
Status: current

Allow access to SM Management from this IP.
0 is default setting to allow from all IPs.

allowedIPAccess3

Object ID: 1.3.6.1.4.1.161.19.3.2.1.71

Syntax: STRING
Constraints: SIZE (4)
Access: read-write
Status: current

Allow access to SM Management from this IP.
0 is default setting to allow from all IPs.

allowedIPAccessNMLength1

Object ID: 1.3.6.1.4.1.161.19.3.2.1.138

Syntax: INTEGER
Constraints: 1..32
Access: read-write
Status: current

Length of the network mask to apply to the AllowedIPAddress when assessing if access is allowed

allowedIPAccessNMLength2

Object ID: 1.3.6.1.4.1.161.19.3.2.1.139

Syntax: INTEGER
Constraints: 1..32
Access: read-write
Status: current

Length of the network mask to apply to the AllowedIPAddress when assessing if access is allowed

allowedIPAccessNMLength3

Object ID: 1.3.6.1.4.1.161.19.3.2.1.140

Syntax: INTEGER
Constraints: 1..32
Access: read-write
Status: current

Length of the network mask to apply to the AllowedIPAddress when assessing if access is allowed

alternateDNSIP

Object ID: 1.3.6.1.4.1.161.19.3.2.1.29

Syntax: STRING
Constraints: SIZE (4)
Access: read-write
Status: current

The alternate DNS IP when we are configured for static DNS
(Not used when configured for automatic DNS).

apSelection

Object ID: 1.3.6.1.4.1.161.19.3.2.1.132

Syntax: INTEGER
Constraints:

0: optimizeForThroughput

1: powerLevel

Access: read-write
Status: current

This OID affects what AP to attempt to register to when Canopy SMs scan see more than one AP that are valid in it's configuration.
(0) - Default, Canopy radios after scanning select the best AP that will optimize for estimated throughput.
(1) - Select the AP with the best receive power level.
Note this is only if multiple APs fit the current scan configuration, and will be overriden by color codes, RADIUS, etc.

arpCacheTimeout

Object ID: 1.3.6.1.4.1.161.19.3.2.1.20

Syntax: INTEGER
Access: read-write
Status: current

ARP cache time out in unit of minutes. For multipoint only.
Range from 1-30.

arpFilter

Object ID: 1.3.6.1.4.1.161.19.3.2.1.41

Syntax: INTEGER
Constraints:

0: filterOff

1: filterOn

Access: read-write
Status: obsolete

To set ARP packet filter when NAT is disabled.
Obsolete - Use corresponding OID in whipsBoxConfig MIB.

authKeyOption

Object ID: 1.3.6.1.4.1.161.19.3.2.1.9

Syntax: INTEGER
Constraints:

0: useDefault

1: useKeySet

Access: read-write
Status: current

This option is for SMs only. Backhaul timing slave always
uses the set key.
0 - Use default key.
1 - Use set key.

authKeySm

Object ID: 1.3.6.1.4.1.161.19.3.2.1.7

Syntax: OCTET STRING
Constraints: SIZE (0..255)
Access: read-write
Status: current

Authentication key. It should be equal or less than 32
characters long.

authOuterId

Object ID: 1.3.6.1.4.1.161.19.3.2.7.6

Syntax: OCTET STRING
Constraints: SIZE (0..253)
Access: read-write
Status: current

EAP Peer Username

authPassword

Object ID: 1.3.6.1.4.1.161.19.3.2.7.7

Syntax: OCTET STRING
Constraints: SIZE (0..255)
Access: read-write
Status: current

EAP Peer password

authUsername

Object ID: 1.3.6.1.4.1.161.19.3.2.7.8

Syntax: OCTET STRING
Constraints: SIZE (0..255)
Access: read-write
Status: current

EAP Peer Identity

authenticationEnforce

Object ID: 1.3.6.1.4.1.161.19.3.2.7.3

Syntax: INTEGER
Constraints:

0: disable

1: aaa

2: presharedkey

Access: read-write
Status: current

enforce SM to register with specifed Auth Enabled AP

bCastMIR

Object ID: 1.3.6.1.4.1.161.19.3.2.1.73

Syntax: INTEGER
Constraints:

0: disabled

Access: read-write
Status: current

To enable and set Broadcast/ Multicast MIR feature. Use value of 0 to disable. Units are in kbps

bandwidthScan

Object ID: 1.3.6.1.4.1.161.19.3.2.1.131

Syntax: OCTET STRING
Constraints: SIZE (0..255)
Access: read-write
Status: current

Bandwidth values for frequency scanning used by MIMO SMs only.
When setting use a comma delimited list of bandwidths.
For example: 10, 20

beaconsPercentReceived

Object ID: 1.3.6.1.4.1.161.19.3.2.2.139

Syntax: INTEGER
Constraints: 0..100
Access: read-only
Status: current

The current percentage of beacons that the SM/BHS successfully receiving.

berDeModSelect

Object ID: 1.3.6.1.4.1.161.19.3.2.1.143

Syntax: INTEGER
Constraints:

0: qpsk

1: qam-16

2: qam-64

3: qam-256

Access: read-write
Status: current

The BER demodulation level the SM is set. 0 for QPSK, 1 for 16-QAM, 2 for 64-QAM, and 3 for 256-QAM.

berPwrRxFPGAPathA

Object ID: 1.3.6.1.4.1.161.19.3.2.2.123

Syntax: INTEGER
Access: read-only
Status: current

BER power level on FPGA Rx Path A of SM.

berPwrRxFPGAPathB

Object ID: 1.3.6.1.4.1.161.19.3.2.2.124

Syntax: INTEGER
Access: read-only
Status: current

BER power level on FPGA Rx Path B of SM.

berrautoupdateflag

Object ID: 1.3.6.1.4.1.161.19.3.2.1.136

Syntax: INTEGER
Access: read-write
Status: current

This indicates if the once a second BERR updating of counters is enabled. 1 = enabled 0 = disabled

bhsReReg

Object ID: 1.3.6.1.4.1.161.19.3.2.1.74

Syntax: INTEGER
Constraints:

0: disabled

1: enabled

Access: read-write
Status: obsolete

Allows BHS re-registration every 24 hours. Enable allows re-registration and Disable does not. 24 Hour Encryption Refresh.

bitErrors16QAMpathA

Object ID: 1.3.6.1.4.1.161.19.3.2.2.132

Syntax: Counter
Constraints: 0..18446744073709551615
Access: read-only
Status: current

Number of bit errors received from BER packet at 16-QAM path A.
Valid MIMO platforms only.
Engineering use only.

bitErrors16QAMpathB

Object ID: 1.3.6.1.4.1.161.19.3.2.2.133

Syntax: Counter
Constraints: 0..18446744073709551615
Access: read-only
Status: current

Number of bit errors received from BER packet at 16-QAM path B.
Valid MIMO platforms only.
Engineering use only.

bitErrors256QAMpathA

Object ID: 1.3.6.1.4.1.161.19.3.2.2.136

Syntax: Counter
Constraints: 0..18446744073709551615
Access: read-only
Status: current

Number of bit errors received from BER packet at 256-QAM path A.
Valid MIMO platforms only.
Engineering use only.

bitErrors256QAMpathB

Object ID: 1.3.6.1.4.1.161.19.3.2.2.137

Syntax: Counter
Constraints: 0..18446744073709551615
Access: read-only
Status: current

Number of bit errors received from BER packet at 256-QAM path B.
Valid MIMO platforms only.
Engineering use only.

bitErrors64QAMpathA

Object ID: 1.3.6.1.4.1.161.19.3.2.2.134

Syntax: Counter
Constraints: 0..18446744073709551615
Access: read-only
Status: current

Number of bit errors received from BER packet at 64-QAM path A.
Valid MIMO platforms only.
Engineering use only.

bitErrors64QAMpathB

Object ID: 1.3.6.1.4.1.161.19.3.2.2.135

Syntax: Counter
Constraints: 0..18446744073709551615
Access: read-only
Status: current

Number of bit errors received from BER packet at 64-QAM path B.
Valid MIMO platforms only.
Engineering use only.

bitErrorsQSPKpathA

Object ID: 1.3.6.1.4.1.161.19.3.2.2.130

Syntax: Counter
Constraints: 0..18446744073709551615
Access: read-only
Status: current

Number of bit errors received from BER packet at QPSK path A.
Valid MIMO platforms only.

bitErrorsQSPKpathB

Object ID: 1.3.6.1.4.1.161.19.3.2.2.131

Syntax: Counter
Constraints: 0..18446744073709551615
Access: read-only
Status: current

Number of bit errors received from BER packet at QPSK path B.
Valid MIMO platforms only.

bitsReceivedPerPathModulation

Object ID: 1.3.6.1.4.1.161.19.3.2.2.138

Syntax: Counter
Constraints: 0..18446744073709551615
Access: read-only
Status: current

Number of bit received from BER.
To calculate Bit Error Rate, take bit errors at a modulation and path and divide by this OID.
To get combined BER add errors and divide by this multiplied by each path and modulation.
i.e. MIMO QPSK combined BER = ((errors on path A) + (errors on path B))/(bits recieved per path modulation * 2)
Valid MIMO platforms only.

bootpcFilter

Object ID: 1.3.6.1.4.1.161.19.3.2.1.52

Syntax: INTEGER
Constraints:

0: filterOff

1: filterOn

Access: read-write
Status: obsolete

To set bootp client sourced packets filter when
NAT is disabled.
Obsolete - Use corresponding OID in whipsBoxConfig MIB.

bootpsFilter

Object ID: 1.3.6.1.4.1.161.19.3.2.1.53

Syntax: INTEGER
Constraints:

0: filterOff

1: filterOn

Access: read-write
Status: obsolete

To set bootp server sourced packets filter when
NAT is disabled.
Obsolete - Use corresponding OID in whipsBoxConfig MIB.

bridgecbDownlinkCreditLimit

Object ID: 1.3.6.1.4.1.161.19.3.2.2.100

Syntax: Gauge
Constraints: 0..4294967295
Access: read-only
Status: current

Uplink Burst Allocation.

bridgecbDownlinkCreditRate

Object ID: 1.3.6.1.4.1.161.19.3.2.2.99

Syntax: Gauge
Constraints: 0..4294967295
Access: read-only
Status: current

Sustained uplink data rate.

bridgecbDownlinkMaxBurstBitRate

Object ID: 1.3.6.1.4.1.161.19.3.2.2.119

Syntax: Gauge
Constraints: 0..4294967295
Access: read-only
Status: current

Maximum burst downlink rate.

bridgecbUplinkCreditLimit

Object ID: 1.3.6.1.4.1.161.19.3.2.2.98

Syntax: Gauge
Constraints: 0..4294967295
Access: read-only
Status: current

Uplink Burst Allocation.

bridgecbUplinkCreditRate

Object ID: 1.3.6.1.4.1.161.19.3.2.2.97

Syntax: Gauge
Constraints: 0..4294967295
Access: read-only
Status: current

Sustained uplink data rate.

bridgecbUplinkMaxBurstBitRate

Object ID: 1.3.6.1.4.1.161.19.3.2.2.120

Syntax: Gauge
Constraints: 0..4294967295
Access: read-only
Status: current

Maximum burst uplink Rate.

calibrationStatus

Object ID: 1.3.6.1.4.1.161.19.3.2.2.7

Syntax: OCTET STRING
Constraints: SIZE (0..255)
Access: read-only
Status: deprecated

Varible deprecated. Please use calibrationStatusBox.

cert

Object ID: 1.3.6.1.4.1.161.19.3.2.7.1.1.2

Syntax: INTEGER
Constraints:

0: inactive

1: active

Access: read-only
Status: current

0: Inactive 1: Active

certEntry

Object ID: 1.3.6.1.4.1.161.19.3.2.7.1.1

Syntax: Sequence (Structure)

certIndex

cert

action

certificateDN

Access: not-accessible
Status: current

Entry of Certifcates.

certIndex

Object ID: 1.3.6.1.4.1.161.19.3.2.7.1.1.1

Syntax: INTEGER
Constraints: 1..2
Access: read-only
Status: current

User information table index.

certTable

Object ID: 1.3.6.1.4.1.161.19.3.2.7.1

Syntax: Sequence of Type (Array)

CertEntry

Access: not-accessible
Status: current

The table of CA Certificates on SM.

certificateDN

Object ID: 1.3.6.1.4.1.161.19.3.2.7.1.1.4

Syntax: OCTET STRING
Constraints: SIZE (0..255)
Access: read-only
Status: current

Distinguished Name of Certificate 2

clearBerrResults

Object ID: 1.3.6.1.4.1.161.19.3.2.1.135

Syntax: INTEGER
Access: read-write
Status: current

This will clear the BERR results.

clearLinkStats

Object ID: 1.3.6.1.4.1.161.19.3.2.8.1

Syntax: INTEGER
Access: read-write
Status: current

Setting this to a nonzero value will clear the link stats.

colorCode10

Object ID: 1.3.6.1.4.1.161.19.3.2.1.113

Syntax: INTEGER
Constraints: 0..254
Access: read-write
Status: current

Tenth Color code.

colorCode2

Object ID: 1.3.6.1.4.1.161.19.3.2.1.97

Syntax: INTEGER
Constraints: 0..254
Access: read-write
Status: current

Second Color code.

colorCode3

Object ID: 1.3.6.1.4.1.161.19.3.2.1.99

Syntax: INTEGER
Constraints: 0..254
Access: read-write
Status: current

Third Color code.

colorCode4

Object ID: 1.3.6.1.4.1.161.19.3.2.1.101

Syntax: INTEGER
Constraints: 0..254
Access: read-write
Status: current

Fourth Color code.

colorCode5

Object ID: 1.3.6.1.4.1.161.19.3.2.1.103

Syntax: INTEGER
Constraints: 0..254
Access: read-write
Status: current

Fifth Color code.

colorCode6

Object ID: 1.3.6.1.4.1.161.19.3.2.1.105

Syntax: INTEGER
Constraints: 0..254
Access: read-write
Status: current

Sixth Color code.

colorCode7

Object ID: 1.3.6.1.4.1.161.19.3.2.1.107

Syntax: INTEGER
Constraints: 0..254
Access: read-write
Status: current

Seventh Color code.

colorCode8

Object ID: 1.3.6.1.4.1.161.19.3.2.1.109

Syntax: INTEGER
Constraints: 0..254
Access: read-write
Status: current

Eighth Color code.

colorCode9

Object ID: 1.3.6.1.4.1.161.19.3.2.1.111

Syntax: INTEGER
Constraints: 0..254
Access: read-write
Status: current

Ninth Color code.

colorCodepriority10

Object ID: 1.3.6.1.4.1.161.19.3.2.1.114

Syntax: INTEGER
Constraints:

0: disable

1: primary

2: secondary

3: tertiary

Access: read-write
Status: current

Priority setting for the tenth color code.

colorCodepriority2

Object ID: 1.3.6.1.4.1.161.19.3.2.1.98

Syntax: INTEGER
Constraints:

0: disable

1: primary

2: secondary

3: tertiary

Access: read-write
Status: current

Priority setting for second color code.

colorCodepriority3

Object ID: 1.3.6.1.4.1.161.19.3.2.1.100

Syntax: INTEGER
Constraints:

0: disable

1: primary

2: secondary

3: tertiary

Access: read-write
Status: current

Priority setting for the third color code.

colorCodepriority4

Object ID: 1.3.6.1.4.1.161.19.3.2.1.102

Syntax: INTEGER
Constraints:

0: disable

1: primary

2: secondary

3: tertiary

Access: read-write
Status: current

Priority setting for the fourth color code.

colorCodepriority5

Object ID: 1.3.6.1.4.1.161.19.3.2.1.104

Syntax: INTEGER
Constraints:

0: disable

1: primary

2: secondary

3: tertiary

Access: read-write
Status: current

Priority setting for the fifth color code.

colorCodepriority6

Object ID: 1.3.6.1.4.1.161.19.3.2.1.106

Syntax: INTEGER
Constraints:

0: disable

1: primary

2: secondary

3: tertiary

Access: read-write
Status: current

Priority setting for the sixth color code.

colorCodepriority7

Object ID: 1.3.6.1.4.1.161.19.3.2.1.108

Syntax: INTEGER
Constraints:

0: disable

1: primary

2: secondary

3: tertiary

Access: read-write
Status: current

Priority setting for the seventh color code.

colorCodepriority8

Object ID: 1.3.6.1.4.1.161.19.3.2.1.110

Syntax: INTEGER
Constraints:

0: disable

1: primary

2: secondary

3: tertiary

Access: read-write
Status: current

Priority setting for the eighth color code.

colorCodepriority9

Object ID: 1.3.6.1.4.1.161.19.3.2.1.112

Syntax: INTEGER
Constraints:

0: disable

1: primary

2: secondary

3: tertiary

Access: read-write
Status: current

Priority setting for the ninth color code.

currentBandwidth

Object ID: 1.3.6.1.4.1.161.19.3.2.2.122

Syntax: INTEGER
Constraints:

1: bandwidth5mhz

3: bandwidth10mhz

5: bandwidth20mhz

Access: read-only
Status: current

The Current Bandwidth of the AP/BHM when in session.

currentChanFreq

Object ID: 1.3.6.1.4.1.161.19.3.2.2.67

Syntax: Gauge
Constraints: 0..4294967295
Access: read-only
Status: current

The Current Channel Frequency of the AP/BHM when in session.

currentColorCode

Object ID: 1.3.6.1.4.1.161.19.3.2.2.65

Syntax: INTEGER
Access: read-only
Status: current

The current Color Code of the Registered AP/BHM. A value of -1 is return when the device is not registered.

currentColorCodePri

Object ID: 1.3.6.1.4.1.161.19.3.2.2.66

Syntax: INTEGER
Constraints:

0: none

1: primary

2: secondary

3: tertiary

Access: read-only
Status: current

The current priority of the Registered color code

currentCyclicPrefix

Object ID: 1.3.6.1.4.1.161.19.3.2.2.121

Syntax: INTEGER
Constraints:

0: one-quarter

1: one-eighth

2: one-sixteenth

Access: read-only
Status: current

The Current Cyclic Prefix of the AP/BHM when in session.

cyclicPrefixScan

Object ID: 1.3.6.1.4.1.161.19.3.2.1.130

Syntax: OCTET STRING
Constraints: SIZE (0..255)
Access: read-write
Status: current

Cyclic Prefix value for frequency scanning used by MIMO SMs only.
When setting use a comma delimited list of cyclic prefixes with no spaces. For example: 1/8,1/16

defaultGwSm

Object ID: 1.3.6.1.4.1.161.19.3.2.1.5

Syntax: STRING
Constraints: SIZE (4)
Access: read-write
Status: current

Default gateway.

dfsConfig

Object ID: 1.3.6.1.4.1.161.19.3.2.1.66

Syntax: INTEGER
Constraints:

0: disable

1: enable

Access: read-write
Status: obsolete

To configure proper regions for Dynamic Frequency Shifting. For 5.2/5.4/5.7 GHz radios.

dfsStatus

Object ID: 1.3.6.1.4.1.161.19.3.2.2.22

Syntax: OCTET STRING
Constraints: SIZE (0..255)
Access: read-only
Status: current

Dynamic frequency shifting status. For DFS Radio only.

dhcpCSMask

Object ID: 1.3.6.1.4.1.161.19.3.2.2.13

Syntax: STRING
Constraints: SIZE (4)
Access: read-only
Status: current

Public DHCP server subnet mask.

dhcpCip

Object ID: 1.3.6.1.4.1.161.19.3.2.2.10

Syntax: STRING
Constraints: SIZE (4)
Access: read-only
Status: current

Assigned IP address to DHCP client.

dhcpClientEnable

Object ID: 1.3.6.1.4.1.161.19.3.2.1.23

Syntax: INTEGER
Constraints:

0: disabled

1: enabled

Access: read-write
Status: obsolete

To enable or disable DHCP client. For multipoint SM's
with NAPT enabled.

dhcpClientLease

Object ID: 1.3.6.1.4.1.161.19.3.2.2.12

Syntax: INTEGER
Constraints: 0..4294967295
Access: read-only
Status: current

DHCP client lease time.

dhcpDfltRterIP

Object ID: 1.3.6.1.4.1.161.19.3.2.2.14

Syntax: STRING
Constraints: SIZE (4)
Access: read-only
Status: current

Public default router IP address.

dhcpDomName

Object ID: 1.3.6.1.4.1.161.19.3.2.2.18

Syntax: OCTET STRING
Constraints: SIZE (0..255)
Access: read-only
Status: current

Public domain name server.

dhcpIPStart

Object ID: 1.3.6.1.4.1.161.19.3.2.1.26

Syntax: STRING
Constraints: SIZE (4)
Access: read-write
Status: current

The last byte will be set for the starting IP that
our DHCP server gives away. The first 3 bytes of the
starting IP are the same as those of NAPT private IP

dhcpNumIPsToLease

Object ID: 1.3.6.1.4.1.161.19.3.2.1.32

Syntax: INTEGER
Access: read-write
Status: current

Number of IP addresses that our DHCP server can give away.

dhcpServerEnable

Object ID: 1.3.6.1.4.1.161.19.3.2.1.24

Syntax: INTEGER
Constraints:

0: disabled

1: enabled

Access: read-write
Status: current

To enable or disable DHCP server. For multipoint SM's
with NAPT enabled.

dhcpServerEntry

Object ID: 1.3.6.1.4.1.161.19.3.2.2.19.1

Syntax: Sequence (Structure)

hostIp

hostMacAddress

hostLease

Access: not-accessible
Status: current

Entry of DHCP server hosts.

dhcpServerLeaseTime

Object ID: 1.3.6.1.4.1.161.19.3.2.1.25

Syntax: INTEGER
Access: read-write
Status: current

Units of days for DHCP server lease time. For multipoint
SM's with NAPT enabled. Range from 1-30.

dhcpServerPktRcv

Object ID: 1.3.6.1.4.1.161.19.3.2.2.73

Syntax: Counter
Constraints: 0..4294967295
Access: read-only
Status: current

Number of packets received by SM DHCP Server

dhcpServerPktToss

Object ID: 1.3.6.1.4.1.161.19.3.2.2.74

Syntax: Counter
Constraints: 0..4294967295
Access: read-only
Status: current

Number of packets tossed by SM DHCP Server

dhcpServerPktXmt

Object ID: 1.3.6.1.4.1.161.19.3.2.2.72

Syntax: Counter
Constraints: 0..4294967295
Access: read-only
Status: current

Number of packets transmitted by SM DHCP Server

dhcpServerTable

Object ID: 1.3.6.1.4.1.161.19.3.2.2.19

Syntax: Sequence of Type (Array)

DhcpServerEntry

Access: not-accessible
Status: current

The table of DHCP server hosts.

dhcpSip

Object ID: 1.3.6.1.4.1.161.19.3.2.2.11

Syntax: STRING
Constraints: SIZE (4)
Access: read-only
Status: current

Public DHCP server IP.

dhcpcdns1

Object ID: 1.3.6.1.4.1.161.19.3.2.2.15

Syntax: STRING
Constraints: SIZE (4)
Access: read-only
Status: current

Primary public domain name server.

dhcpcdns2

Object ID: 1.3.6.1.4.1.161.19.3.2.2.16

Syntax: STRING
Constraints: SIZE (4)
Access: read-only
Status: current

Secondary public domain name server.

dhcpcdns3

Object ID: 1.3.6.1.4.1.161.19.3.2.2.17

Syntax: STRING
Constraints: SIZE (4)
Access: read-only
Status: current

Third public domain name server.

dmzEnable

Object ID: 1.3.6.1.4.1.161.19.3.2.1.31

Syntax: INTEGER
Constraints:

0: disabled

1: enabled

Access: read-write
Status: current

To enable or disable DMZ host functionality.

dmzIP

Object ID: 1.3.6.1.4.1.161.19.3.2.1.30

Syntax: STRING
Constraints: SIZE (4)
Access: read-write
Status: current

Only the last byte of DMZ Host IP will be set.
The first 3 bytes of DMZ IP are the same as those of
NAPT private IP.

dnsAutomatic

Object ID: 1.3.6.1.4.1.161.19.3.2.1.27

Syntax: INTEGER
Constraints:

0: manually

1: automatically

Access: read-write
Status: current

To have DHCP Server obtain DNS information automatically or manually.

dwnLnkDataRate

Object ID: 1.3.6.1.4.1.161.19.3.2.1.64

Syntax: INTEGER
Access: read-write
Status: current

Sustained downlink bandwidth cap.

dwnLnkLimit

Object ID: 1.3.6.1.4.1.161.19.3.2.1.65

Syntax: INTEGER
Access: read-write
Status: current

Burst downlink bandwidth cap.

dwnLnkMaxBurstDataRate

Object ID: 1.3.6.1.4.1.161.19.3.2.1.129

Syntax: INTEGER
Access: read-write
Status: current

Maximum burst downlink rate.

eapPeerAAAServerCommonName

Object ID: 1.3.6.1.4.1.161.19.3.2.1.126

Syntax: OCTET STRING
Constraints: SIZE (0..255)
Access: read-write
Status: current

THIS OID IS CURRENTLY UNUSED: EAP Peer Server Common Name

enable8023link

Object ID: 1.3.6.1.4.1.161.19.3.2.1.8

Syntax: INTEGER
Constraints:

0: disabled

1: enabled

Access: read-write
Status: current

To enable or disable 802.3 link. For SMs only.

ethAccessEnable

Object ID: 1.3.6.1.4.1.161.19.3.2.1.76

Syntax: INTEGER
Constraints:

0: disable

1: enable

Access: read-write
Status: current

To enable or disable Ethernet Port access to SM Management Functions.
(1) - Ethernet access to SM Management allowed.
(0) - Ethernet access to SM Management blocked.

ethAccessFilterEnable

Object ID: 1.3.6.1.4.1.161.19.3.2.1.67

Syntax: INTEGER
Constraints:

0: disable

1: enable

Access: read-write
Status: obsolete

To enable or disable Ethernet Port access filtering to SM Management Functions.
(0) - Ethernet access to SM Management allowed.
(1) - Ethernet access to SM Management blocked.

forcepoweradjust

Object ID: 1.3.6.1.4.1.161.19.3.2.1.134

Syntax: INTEGER
Access: read-write
Status: current

This will force a multipoint SM to initiate an asynchronous power adjust sequence.

fragmentsReceived1XHorizontal

Object ID: 1.3.6.1.4.1.161.19.3.2.2.109

Syntax: Counter
Constraints: 0..4294967295
Access: read-only
Status: current

Engineering use only.
Number of fragments received in 1x modulation.
For MIMO radios only.
For MIMO this is the horizontal path.
Fragments received in MIMO-A will only be counted on vertical.

fragmentsReceived1XVertical

Object ID: 1.3.6.1.4.1.161.19.3.2.2.87

Syntax: Counter
Constraints: 0..4294967295
Access: read-only
Status: current

Engineering use only.
Number of fragments received in 1x modulation.
For GenII OFDM only and forward.
For MIMO this is the vertical path.

fragmentsReceived2XHorizontal

Object ID: 1.3.6.1.4.1.161.19.3.2.2.110

Syntax: Counter
Constraints: 0..4294967295
Access: read-only
Status: current

Engineering use only.
Number of fragments received in 2x modulation.
For MIMO radios only.
For MIMO this is the horizontal path.
Fragments received in MIMO-A will only be counted on vertical.

fragmentsReceived2XVertical

Object ID: 1.3.6.1.4.1.161.19.3.2.2.88

Syntax: Counter
Constraints: 0..4294967295
Access: read-only
Status: current

Engineering use only.
Number of fragments received in 2x modulation.
For GenII OFDM only and forward.
For MIMO this is the vertical path.

fragmentsReceived3XHorizontal

Object ID: 1.3.6.1.4.1.161.19.3.2.2.111

Syntax: Counter
Constraints: 0..4294967295
Access: read-only
Status: current

Engineering use only.
Number of fragments received in 3x modulation.
For MIMO radios only.
For MIMO this is the horizontal path.
Fragments received in MIMO-A will only be counted on vertical.

fragmentsReceived3XVertical

Object ID: 1.3.6.1.4.1.161.19.3.2.2.89

Syntax: Counter
Constraints: 0..4294967295
Access: read-only
Status: current

Engineering use only.
Number of fragments received in 3x modulation.
For GenII OFDM only and forward.
For MIMO this is the vertical path.

fragmentsReceived4XHorizontal

Object ID: 1.3.6.1.4.1.161.19.3.2.2.112

Syntax: Counter
Constraints: 0..4294967295
Access: read-only
Status: current

Engineering use only.
Number of fragments received in 4x modulation.
For MIMO radios only.
For MIMO this is the horizontal path.
Fragments received in MIMO-A will only be counted on vertical.

fragmentsReceived4XVertical

Object ID: 1.3.6.1.4.1.161.19.3.2.2.90

Syntax: Counter
Constraints: 0..4294967295
Access: read-only
Status: current

Engineering use only.
Number of fragments received in 4x modulation.
For GenII OFDM only and forward.
For MIMO this is the vertical path.

hiPriorityChannel

Object ID: 1.3.6.1.4.1.161.19.3.2.1.58

Syntax: INTEGER
Constraints:

0: disabled

1: enable

Access: read-write
Status: current

To enable or disable high priority channel.

hiPriorityDownlinkCIR

Object ID: 1.3.6.1.4.1.161.19.3.2.1.60

Syntax: INTEGER
Access: read-write
Status: current

High priority downlink CIR.

hiPriorityUplinkCIR

Object ID: 1.3.6.1.4.1.161.19.3.2.1.59

Syntax: INTEGER
Access: read-write
Status: current

High priority uplink CIR.

hostIp

Object ID: 1.3.6.1.4.1.161.19.3.2.2.19.1.1

Syntax: STRING
Constraints: SIZE (4)
Access: read-only
Status: current

DHCP server IP address.

hostLease

Object ID: 1.3.6.1.4.1.161.19.3.2.2.19.1.3

Syntax: INTEGER
Constraints: 0..4294967295
Access: read-only
Status: current

Lease time assigned by DHCP server host.

hostMacAddress

Object ID: 1.3.6.1.4.1.161.19.3.2.2.19.1.2

Syntax: OCTET STRING
Access: read-only
Status: current

Private host MAC address.

ingressVID

Object ID: 1.3.6.1.4.1.161.19.3.2.1.55

Syntax: INTEGER
Access: read-write
Status: current

Untagged ingress VID.

ingressVIDPriority

Object ID: 1.3.6.1.4.1.161.19.3.2.1.148

Syntax: INTEGER
Constraints: 0..7
Access: read-write
Status: current

ingress VID VLAN Priority.

ingressVIDPriorityMode

Object ID: 1.3.6.1.4.1.161.19.3.2.1.149

Syntax: INTEGER
Constraints:

0: promote-IP-priority

1: define-priority

Access: read-write
Status: current

ingress VID VLAN Priority Mode.

ip4MultFilter

Object ID: 1.3.6.1.4.1.161.19.3.2.1.54

Syntax: INTEGER
Constraints:

0: filterOff

1: filterOn

Access: read-write
Status: obsolete

To set IPv4 MultiCast packets filter when
NAT is disabled.
Obsolete - Use corresponding OID in whipsBoxConfig MIB.

ipAccessFilterEnable

Object ID: 1.3.6.1.4.1.161.19.3.2.1.68

Syntax: INTEGER
Constraints:

0: disable

1: enable

Access: read-write
Status: current

To enable or disable IP access filtering to Management functions.
(0) - IP access will be allowed from all addresses.
(1) - IP access will be controlled using allowedIPAccess1-3 entries.

jitter

Object ID: 1.3.6.1.4.1.161.19.3.2.2.3

Syntax: Gauge
Constraints: 0..15
Access: read-only
Status: current

A measure of multipath interference. Applicable to FSK radios only.

lanIpSm

Object ID: 1.3.6.1.4.1.161.19.3.2.1.3

Syntax: STRING
Constraints: SIZE (4)
Access: read-write
Status: current

LAN IP.

lanMaskSm

Object ID: 1.3.6.1.4.1.161.19.3.2.1.4

Syntax: STRING
Constraints: SIZE (4)
Access: read-write
Status: current

LAN subnet mask.

linkQualityBeacon

Object ID: 1.3.6.1.4.1.161.19.3.2.2.68

Syntax: OCTET STRING
Constraints: SIZE (0..255)
Access: read-only
Status: current

Engineering only.
Link Quality for incoming beacons.
For Gen II OFDM radios and forward.
For PMP 450 and forward this is vertical path.

linkQualityData1XHorizontal

Object ID: 1.3.6.1.4.1.161.19.3.2.2.113

Syntax: OCTET STRING
Constraints: SIZE (0..255)
Access: read-only
Status: current

Engineering use only.
Link Quality for the data VC for QPSK modulation (1X).
For MIMO radios only.
For MIMO this is the horizontal path.
Fragments received in MIMO-A will only be counted on vertical.

linkQualityData1XVertical

Object ID: 1.3.6.1.4.1.161.19.3.2.2.91

Syntax: OCTET STRING
Constraints: SIZE (0..255)
Access: read-only
Status: current

Engineering use only.
Link Quality for the data VC for QPSK modulation (1X).
For Gen II OFDM radios and forward only.
For MIMO this is the vertical path.

linkQualityData2XHorizontal

Object ID: 1.3.6.1.4.1.161.19.3.2.2.114

Syntax: OCTET STRING
Constraints: SIZE (0..255)
Access: read-only
Status: current

Engineering use only.
Link Quality for the data VC for 16-QAM modulation (2X).
For MIMO radios only.
For MIMO this is the horizontal path.
Fragments received in MIMO-A will only be counted on vertical.

linkQualityData2XVertical

Object ID: 1.3.6.1.4.1.161.19.3.2.2.92

Syntax: OCTET STRING
Constraints: SIZE (0..255)
Access: read-only
Status: current

Engineering use only.
Link Quality for the data VC for 16-QAM modulation (2X).
For Gen II OFDM radios and forward only.
For MIMO this is the vertical path.

linkQualityData3XHorizontal

Object ID: 1.3.6.1.4.1.161.19.3.2.2.115

Syntax: OCTET STRING
Constraints: SIZE (0..255)
Access: read-only
Status: current

Engineering use only.
Link Quality for the data VC for 64-QAM modulation (3X).
For MIMO radios only.
For MIMO this is the horizontal path.
Fragments received in MIMO-A will only be counted on vertical.

linkQualityData3XVertical

Object ID: 1.3.6.1.4.1.161.19.3.2.2.93

Syntax: OCTET STRING
Constraints: SIZE (0..255)
Access: read-only
Status: current

Engineering use only.
Link Quality for the data VC for 64-QAM modulation (3X).
For Gen II OFDM radios and forward only.
For MIMO this is the vertical path.

linkQualityData4XHorizontal

Object ID: 1.3.6.1.4.1.161.19.3.2.2.116

Syntax: OCTET STRING
Constraints: SIZE (0..255)
Access: read-only
Status: current

Engineering use only.
Link Quality for the data VC for 256-QAM modulation (4X).
For MIMO radios only.
For MIMO this is the horizontal path.
Fragments received in MIMO-A will only be counted on vertical.

linkQualityData4XVertical

Object ID: 1.3.6.1.4.1.161.19.3.2.2.94

Syntax: OCTET STRING
Constraints: SIZE (0..255)
Access: read-only
Status: current

Engineering use only.
Link Quality for the data VC for 256-QAM modulation (4X).
For Gen II OFDM radios and forward only.
For MIMO this is the vertical path.

localIp

Object ID: 1.3.6.1.4.1.161.19.3.2.5.1.4

Syntax: STRING
Constraints: SIZE (4)
Access: read-write
Status: current

IP of local host to which the incoming packet mapped to an application should be forwarded.

lowPriorityDownlinkCIR

Object ID: 1.3.6.1.4.1.161.19.3.2.1.57

Syntax: INTEGER
Access: read-write
Status: current

Low priority downlink CIR.

lowPriorityUplinkCIR

Object ID: 1.3.6.1.4.1.161.19.3.2.1.56

Syntax: INTEGER
Access: read-write
Status: current

Low priority uplink CIR.

mapsPercentReceived

Object ID: 1.3.6.1.4.1.161.19.3.2.2.140

Syntax: INTEGER
Constraints: 0..100
Access: read-only
Status: current

PMP 450 only.
The current percentage of scheduling maps that the SM/BHS successfully receiving.

maxJitter

Object ID: 1.3.6.1.4.1.161.19.3.2.2.35

Syntax: Gauge
Constraints: 0..15
Access: read-only
Status: current

Measured Max. Jitter. Applicable to FSK radios only.

maxRSSI

Object ID: 1.3.6.1.4.1.161.19.3.2.2.33

Syntax: INTEGER
Access: read-only
Status: current

Measured Max. RSSI. Applicable to FSK radios only.

maxRadioDbm

Object ID: 1.3.6.1.4.1.161.19.3.2.2.59

Syntax: INTEGER
Access: read-only
Status: current

Maximum receive power of beacon in dBm.
For MIMO radios, this is only available in the vertical path.

maxRadioDbmDeprecated

Object ID: 1.3.6.1.4.1.161.19.3.2.2.107

Syntax: INTEGER
Access: read-only
Status: deprecated

This OID was inadvertently moved in 12.0.2. Please use maxRadioDbm. This OID is deprecated
and kept for backwards compatibility.

mimo16QamBerDisplay

Object ID: 1.3.6.1.4.1.161.19.3.2.2.102

Syntax: OCTET STRING
Constraints: SIZE (0..255)
Access: read-only
Status: current

16-QAM BER statistics
MIMO platforms only.
Engineering use only.

mimo256QamBerDisplay

Object ID: 1.3.6.1.4.1.161.19.3.2.2.104

Syntax: OCTET STRING
Constraints: SIZE (0..255)
Access: read-only
Status: current

256-QAM BER statistics
MIMO platforms only.
Engineering use only.

mimo64QamBerDisplay

Object ID: 1.3.6.1.4.1.161.19.3.2.2.103

Syntax: OCTET STRING
Constraints: SIZE (0..255)
Access: read-only
Status: current

64-QAM BER statistics
MIMO platforms only.
Engineering use only.

mimoBerRcvModulationType

Object ID: 1.3.6.1.4.1.161.19.3.2.2.105

Syntax: OCTET STRING
Constraints: SIZE (0..255)
Access: read-only
Status: current

Receive modulation type.
MIMO platforms only.

mimoQpskBerDisplay

Object ID: 1.3.6.1.4.1.161.19.3.2.2.101

Syntax: OCTET STRING
Constraints: SIZE (0..255)
Access: read-only
Status: current

QPSK BER statistics.
MIMO platforms only.

minJitter

Object ID: 1.3.6.1.4.1.161.19.3.2.2.34

Syntax: Gauge
Constraints: 0..15
Access: read-only
Status: current

Measured Min. Jitter. Applicable to FSK radios only.

minRSSI

Object ID: 1.3.6.1.4.1.161.19.3.2.2.32

Syntax: INTEGER
Access: read-only
Status: current

Measured Min. RSSI. Applicable to FSK radios only.

minRadioDbm

Object ID: 1.3.6.1.4.1.161.19.3.2.2.58

Syntax: INTEGER
Access: read-only
Status: current

Maximum receive power of beacon in dBm.
For MIMO radios, this is only available in the vertical path.

multicastVCRcvRate

Object ID: 1.3.6.1.4.1.161.19.3.2.1.144

Syntax: OCTET STRING
Constraints: SIZE (0..255)
Access: read-only
Status: current

Multicast VC Receive Rate

naptEnable

Object ID: 1.3.6.1.4.1.161.19.3.2.1.19

Syntax: INTEGER
Constraints:

0: disabled

1: enabled

Access: read-write
Status: current

To enable or disable NAPT. For multipoint only.
1=Enable NAPT, 0=Disable NAPT.

naptPrivateIP

Object ID: 1.3.6.1.4.1.161.19.3.2.1.11

Syntax: STRING
Constraints: SIZE (4)
Access: read-write
Status: current

NAPT private IP address. Only the first three bytes can be
changed when NAPT is enabled.

naptPrivateSubnetMask

Object ID: 1.3.6.1.4.1.161.19.3.2.1.12

Syntax: STRING
Constraints: SIZE (4)
Access: read-write
Status: current

NAPT private subnet mask. Only the last byte can be
changed when NAPT is enabled. The address will always be:
255.255.255.x.

naptPublicGatewayIP

Object ID: 1.3.6.1.4.1.161.19.3.2.1.15

Syntax: STRING
Constraints: SIZE (4)
Access: read-write
Status: current

IP Address of NAPT Public Interface Gateway. The variable is available
only when NAPT is enabled.

naptPublicIP

Object ID: 1.3.6.1.4.1.161.19.3.2.1.13

Syntax: STRING
Constraints: SIZE (4)
Access: read-write
Status: current

IP Address of NAPT Public Interface. The variable is available
only when NAPT is enabled.

naptPublicSubnetMask

Object ID: 1.3.6.1.4.1.161.19.3.2.1.14

Syntax: STRING
Constraints: SIZE (4)
Access: read-write
Status: current

Subnet mask for NAPT Public Interface. The variable is available
only when NAPT is enabled.

naptRFPublicGateway

Object ID: 1.3.6.1.4.1.161.19.3.2.1.18

Syntax: STRING
Constraints: SIZE (4)
Access: read-write
Status: current

IP Address of RF Public Interface Gateway. The variable is
available only when NAPT is enabled.

naptRFPublicIP

Object ID: 1.3.6.1.4.1.161.19.3.2.1.16

Syntax: STRING
Constraints: SIZE (4)
Access: read-write
Status: current

IP Address of RF Public Interface. The variable is available
only when NAPT is enabled.

naptRFPublicSubnetMask

Object ID: 1.3.6.1.4.1.161.19.3.2.1.17

Syntax: STRING
Constraints: SIZE (4)
Access: read-write
Status: current

Subnet mask of RF Public Interface. The variable is available
only when NAPT is enabled.

naptRemoteManage

Object ID: 1.3.6.1.4.1.161.19.3.2.1.141

Syntax: INTEGER
Constraints:

0: disable

1: enable-standalone

2: enable-wan

Access: read-write
Status: current

To enable or disable Remote Management. For multipoint only.
0=Disable Remote Management,
1=Enable - Standalone Config,
2=Enable - Use WAN Interface.

natConnectionType

Object ID: 1.3.6.1.4.1.161.19.3.2.1.94

Syntax: INTEGER
Constraints:

0: staticIP

1: dhcp

2: pppoe

Access: read-write
Status: current

To configure the SM NAT connection type. Options are Static IP, DHCP, or PPPoE.

natDNSProxyEnable

Object ID: 1.3.6.1.4.1.161.19.3.2.1.115

Syntax: INTEGER
Constraints:

0: disabled

1: enabled

Access: read-write
Status: current

If enabled, the SM will advertise itself as the DNS server when it sends out DHCP client leases and forward DNS queries automatically.
If disabled, the SM will forward on upstream DNS server information when it sends out DHCP client leases.

natTslTableEntries

Object ID: 1.3.6.1.4.1.161.19.3.2.2.141

Syntax: INTEGER
Access: read-only
Status: current

Number of Entries in NAT Translation Table.

natTslTableSize

Object ID: 1.3.6.1.4.1.161.19.3.2.1.147

Syntax: INTEGER
Constraints: 1024..8192
Access: read-write
Status: current

NAT Translation Table Size.
Range 1024-8192.

nbBitsRcvd

Object ID: 1.3.6.1.4.1.161.19.3.2.2.26

Syntax: Counter
Constraints: 0..18446744073709551615
Access: read-only
Status: current

Number of BER bits received (non MIMO platforms only).

nbPriBitsErr

Object ID: 1.3.6.1.4.1.161.19.3.2.2.27

Syntax: Counter
Constraints: 0..4294967295
Access: read-only
Status: current

Number of Primary bit errors (non MIMO platforms only).

nbSndBitsErr

Object ID: 1.3.6.1.4.1.161.19.3.2.2.28

Syntax: Counter
Constraints: 0..4294967295
Access: read-only
Status: current

Number of secondary bit errors (non MIMO platforms only).

networkAccess

Object ID: 1.3.6.1.4.1.161.19.3.2.1.6

Syntax: INTEGER
Constraints:

0: localIP

1: publicIP

Access: read-write
Status: current

Network accessibility. Public or local IP.
For multipoint only.

numAuthCerts

Object ID: 1.3.6.1.4.1.161.19.3.2.7.2

Syntax: INTEGER
Access: read-only
Status: current

can have a max value of 2

packetFilterDirection

Object ID: 1.3.6.1.4.1.161.19.3.2.1.96

Syntax: INTEGER
Constraints:

1: upstream

2: downstream

Access: read-write
Status: obsolete

To packet filter direction when NAT is disabled. Upstream is default.
Obsolete - Use corresponding OID in whipsBoxConfig MIB.

phase1

Object ID: 1.3.6.1.4.1.161.19.3.2.7.4

Syntax: INTEGER
Constraints:

0: eapttls

1: eapMSChapV2

Access: read-write
Status: current

Select the outer method for EAP Authentication

phase2

Object ID: 1.3.6.1.4.1.161.19.3.2.7.5

Syntax: INTEGER
Constraints:

0: pap

1: chap

2: mschapv2

Access: read-write
Status: current

Select the outer method for EAP Authentication

pmp430ApRegistrationOptions

Object ID: 1.3.6.1.4.1.161.19.3.2.1.145

Syntax: INTEGER
Constraints:

1: pmp430

2: pmp450

3: both

Access: read-write
Status: current

Selects AP types (430 and/or 450) that are available for the PMP 430 SM. When both AP types are selected, if the SM does not register to an AP, it will reboot to scan the other AP type.

port

Object ID: 1.3.6.1.4.1.161.19.3.2.5.1.3

Syntax: INTEGER
Access: read-write
Status: current

Application port number. e.g. 23=telnet, 21=ftp etc. Should be a positive integer.

port1TCPFilter

Object ID: 1.3.6.1.4.1.161.19.3.2.1.44

Syntax: INTEGER
Constraints:

0: filterOff

1: filterOn

Access: read-write
Status: obsolete

To set user defined port 1 TCP traffic filter.
Obsolete - Use corresponding OID in whipsBoxConfig MIB.

port1UDPFilter

Object ID: 1.3.6.1.4.1.161.19.3.2.1.45

Syntax: INTEGER
Constraints:

0: filterOff

1: filterOn

Access: read-write
Status: obsolete

To set user defined port 1 UDP traffic filter.
Obsolete - Use corresponding OID in whipsBoxConfig MIB.

port2TCPFilter

Object ID: 1.3.6.1.4.1.161.19.3.2.1.47

Syntax: INTEGER
Constraints:

0: filterOff

1: filterOn

Access: read-write
Status: obsolete

To set user defined port 2 TCP traffic filter.
Obsolete - Use corresponding OID in whipsBoxConfig MIB.

port2UDPFilter

Object ID: 1.3.6.1.4.1.161.19.3.2.1.48

Syntax: INTEGER
Constraints:

0: filterOff

1: filterOn

Access: read-write
Status: obsolete

To set user defined port 2 UDP traffic filter.
Obsolete - Use corresponding OID in whipsBoxConfig MIB.

port3TCPFilter

Object ID: 1.3.6.1.4.1.161.19.3.2.1.50

Syntax: INTEGER
Constraints:

0: filterOff

1: filterOn

Access: read-write
Status: obsolete

To set user defined port 3 TCP traffic filter.
Obsolete - Use corresponding OID in whipsBoxConfig MIB.

port3UDPFilter

Object ID: 1.3.6.1.4.1.161.19.3.2.1.51

Syntax: INTEGER
Constraints:

0: filterOff

1: filterOn

Access: read-write
Status: obsolete

To set user defined port 3 UDP traffic filter.
Obsolete - Use corresponding OID in whipsBoxConfig MIB.

powerUpMode

Object ID: 1.3.6.1.4.1.161.19.3.2.1.2

Syntax: INTEGER
Constraints:

0: operational

1: aim

Access: read-write
Status: current

SM Power Up Mode With No 802.3 Link.
1 -- Power up in Aim mode
2 -- Power up in Operational mode.

pppoeACNameStatus

Object ID: 1.3.6.1.4.1.161.19.3.2.2.52

Syntax: OCTET STRING
Constraints: SIZE (0..255)
Access: read-only
Status: current

Current PPPoE Access Concentrator In Use

pppoeAccessConcentrator

Object ID: 1.3.6.1.4.1.161.19.3.2.1.79

Syntax: OCTET STRING
Constraints: SIZE (0..255)
Access: read-write
Status: current

Set the PPPoE Access Concentrator Name. Less than or equal to 32 characters

pppoeAuthenticationType

Object ID: 1.3.6.1.4.1.161.19.3.2.1.78

Syntax: INTEGER
Constraints:

0: none

1: chap-pap

Access: read-write
Status: current

Set the PPPoE Authentication Type to either None or CHAP/pap

pppoeConnectOD

Object ID: 1.3.6.1.4.1.161.19.3.2.1.91

Syntax: INTEGER
Constraints:

1: connectOnDemand

Access: read-write
Status: current

Force a manual PPPoE connection attempt.

pppoeControlBytesReceived

Object ID: 1.3.6.1.4.1.161.19.3.2.2.47

Syntax: Counter
Constraints: 0..4294967295
Access: read-only
Status: current

PPPoE Control Bytes Received

pppoeControlBytesSent

Object ID: 1.3.6.1.4.1.161.19.3.2.2.46

Syntax: Counter
Constraints: 0..4294967295
Access: read-only
Status: current

PPPoE Control Bytes Sent

pppoeDNSServer1

Object ID: 1.3.6.1.4.1.161.19.3.2.2.44

Syntax: STRING
Constraints: SIZE (4)
Access: read-only
Status: current

PPPoE DNS Server 1

pppoeDNSServer2

Object ID: 1.3.6.1.4.1.161.19.3.2.2.45

Syntax: STRING
Constraints: SIZE (4)
Access: read-only
Status: current

PPPoE DNS Server 2

pppoeDataBytesReceived

Object ID: 1.3.6.1.4.1.161.19.3.2.2.49

Syntax: Counter
Constraints: 0..4294967295
Access: read-only
Status: current

PPPoE Data Bytes Received

pppoeDataBytesSent

Object ID: 1.3.6.1.4.1.161.19.3.2.2.48

Syntax: Counter
Constraints: 0..4294967295
Access: read-only
Status: current

PPPoE Data Bytes Sent

pppoeDisconnectOD

Object ID: 1.3.6.1.4.1.161.19.3.2.1.92

Syntax: INTEGER
Constraints:

1: disconnectOnDemand

Access: read-write
Status: current

Force a manual PPPoE disconnection.

pppoeEnable

Object ID: 1.3.6.1.4.1.161.19.3.2.1.77

Syntax: INTEGER
Constraints:

0: disable

1: enable

Access: read-write
Status: current

Enable or disable PPPoE on the SM. NAT MUST be enabled prior and Translation Bridging MUST be DISABLED on the AP.

pppoeEnabledStatus

Object ID: 1.3.6.1.4.1.161.19.3.2.2.50

Syntax: INTEGER
Constraints:

0: disabled

1: enabled

Access: read-only
Status: current

PPPoE Enabled

pppoeFilter

Object ID: 1.3.6.1.4.1.161.19.3.2.1.33

Syntax: INTEGER
Constraints:

0: filterOff

1: filterOn

Access: read-write
Status: obsolete

To set PPPoE packet filter when NAT is disabled.
Obsolete - Use corresponding OID in whipsBoxConfig MIB.

pppoeIPCPAddress

Object ID: 1.3.6.1.4.1.161.19.3.2.2.39

Syntax: STRING
Constraints: SIZE (4)
Access: read-only
Status: current

Current PPPoE IPCP IP Address

pppoeMTUOverrideEn

Object ID: 1.3.6.1.4.1.161.19.3.2.2.40

Syntax: INTEGER
Constraints:

0: disabled

1: enabled

Access: read-only
Status: current

Current PPPoE MTU Override Setting

pppoeMTUOverrideEnable

Object ID: 1.3.6.1.4.1.161.19.3.2.1.84

Syntax: INTEGER
Constraints:

0: disable

1: enable

Access: read-write
Status: current

Enable the overriding of the PPP link's MTU. Normally, the PPP link will set the MTU to the MRU of the
PPPoE Server, but this may be overridden. If the MRU of the PPPoE server is smaller than the desired MTU,
the smaller MTU will be used.

pppoeMTUOverrideValue

Object ID: 1.3.6.1.4.1.161.19.3.2.1.85

Syntax: INTEGER
Constraints: 0..1492
Access: read-write
Status: current

Enable the overriding of the PPP link's MTU. Normally, the PPP link will set the MTU to the MRU of the
PPPoE Server, but this may be overridden. If the MRU of the PPPoE server is smaller than the desired MTU,
the smaller MTU will be used. Max MTU of a PPPoE link is 1492.

pppoeMTUValue

Object ID: 1.3.6.1.4.1.161.19.3.2.2.41

Syntax: INTEGER
Access: read-only
Status: current

Current PPPoE MTU Value

pppoePassword

Object ID: 1.3.6.1.4.1.161.19.3.2.1.82

Syntax: OCTET STRING
Constraints: SIZE (0..255)
Access: read-write
Status: current

Set the PPPoE Password. Less than or equal to 32 characters

pppoeServiceName

Object ID: 1.3.6.1.4.1.161.19.3.2.1.80

Syntax: OCTET STRING
Constraints: SIZE (0..255)
Access: read-write
Status: current

Set the PPPoE Service Name. Less than or equal to 32 characters

pppoeSessIdleTime

Object ID: 1.3.6.1.4.1.161.19.3.2.2.60

Syntax: INTEGER
Constraints: 0..4294967295
Access: read-only
Status: current

Idle Time of current PPPoE Session in ticks

pppoeSessUptime

Object ID: 1.3.6.1.4.1.161.19.3.2.2.54

Syntax: INTEGER
Constraints: 0..4294967295
Access: read-only
Status: current

Uptime of current PPPoE Session in ticks

pppoeSessionID

Object ID: 1.3.6.1.4.1.161.19.3.2.2.38

Syntax: INTEGER
Access: read-only
Status: current

Current PPPoE Session ID

pppoeSessionStatus

Object ID: 1.3.6.1.4.1.161.19.3.2.2.37

Syntax: OCTET STRING
Constraints: SIZE (0..255)
Access: read-only
Status: current

Current PPPoE Session Status

pppoeSvcNameStatus

Object ID: 1.3.6.1.4.1.161.19.3.2.2.53

Syntax: OCTET STRING
Constraints: SIZE (0..255)
Access: read-only
Status: current

Current PPPoE Service Name In Use

pppoeTCPMSSClampEnable

Object ID: 1.3.6.1.4.1.161.19.3.2.1.83

Syntax: INTEGER
Constraints:

0: disable

1: enable

Access: read-write
Status: current

Enable or disable TCP MSS Clamping. Enabling this will cause the SM to edit the TCP MSS in TCP SYN and SYN-ACK packets.
This will allow for a workaround for MTU issues so that the TCP session will only go up to the clamped MSS. If you are
using PMTUD reliably, this should not be needed.

pppoeTCPMSSClampEnableStatus

Object ID: 1.3.6.1.4.1.161.19.3.2.2.51

Syntax: INTEGER
Constraints:

0: disabled

1: enabled

Access: read-only
Status: current

PPPoE TCP MSS Clamping Enable

pppoeTimeoutPeriod

Object ID: 1.3.6.1.4.1.161.19.3.2.1.87

Syntax: INTEGER
Access: read-write
Status: current

The Timeout Period. The use of this depends on the Timer Type. If the Timer Type is KeepAlive, then
the timeout period is in seconds. If the Timer Type is Idle Timeout, then the timeout period is in minutes.
Minimum values are 20 seconds for KeepAlive timer, and 5 minutes for Idle Timeout.

pppoeTimeoutValue

Object ID: 1.3.6.1.4.1.161.19.3.2.2.43

Syntax: INTEGER
Access: read-only
Status: current

Current PPPoE Timeout Period. The use of this depends on the Timer Type. If the Timer Type is KeepAlive, then
the timeout period is in seconds. If the Timer Type is Idle Timeout, then the timeout period is in minutes.

pppoeTimerType

Object ID: 1.3.6.1.4.1.161.19.3.2.1.86

Syntax: INTEGER
Constraints:

1: keepAlive

2: idleTimeout

Access: read-write
Status: current

Set the PPPoE Timer type. Can be a Keep Alive timer where the link will be checked periodically and
automatically redialed if the link is down. Also could be an Idle Timeout where the link will
be automatically dropped after an idle period and redialed if user data is present. Keep Alive timers
are in seconds while Idle Timeout timers are in minutes.

pppoeTimerTypeValue

Object ID: 1.3.6.1.4.1.161.19.3.2.2.42

Syntax: INTEGER
Constraints:

0: disabled

1: keepAlive

2: idleTimeout

Access: read-only
Status: current

Current PPPoE Timer Type. 0 is disabled, 1 is Keep Alive timer, and 2 is Idle Timeout timer.

pppoeUserName

Object ID: 1.3.6.1.4.1.161.19.3.2.1.81

Syntax: OCTET STRING
Constraints: SIZE (0..255)
Access: read-write
Status: current

Set the PPPoE Username. Less than or equal to 32 characters

prefferedDNSIP

Object ID: 1.3.6.1.4.1.161.19.3.2.1.28

Syntax: STRING
Constraints: SIZE (4)
Access: read-write
Status: current

The preferred DNS IP when we are configured for static DNS
(Not used when configured for automatic DNS).

primaryBER

Object ID: 1.3.6.1.4.1.161.19.3.2.2.29

Syntax: INTEGER
Access: read-only
Status: obsolete

Obsoleted, invalid type to represent this data. Measured Primary Bit Error Rate.

primaryBERDisplay

Object ID: 1.3.6.1.4.1.161.19.3.2.2.55

Syntax: OCTET STRING
Constraints: SIZE (0..255)
Access: read-only
Status: current

Measured Primary Bit Error Rate.
Non MIMO platforms only.

protocol

Object ID: 1.3.6.1.4.1.161.19.3.2.5.1.2

Syntax: INTEGER
Access: read-write
Status: current

Protocol type: 0:both UDP and TCP, 1:UDP, 2:TCP.

providerVIDPriority

Object ID: 1.3.6.1.4.1.161.19.3.2.1.150

Syntax: INTEGER
Constraints: 0..7
Access: read-write
Status: current

Provider VID VLAN Priority.

providerVIDPriorityMode

Object ID: 1.3.6.1.4.1.161.19.3.2.1.151

Syntax: INTEGER
Constraints:

0: promote-IP-priority

1: define-priority

2: copy-inner-tag-priority

Access: read-write
Status: current

Provider VID VLAN Priority Mode.

radioBandscanConfig

Object ID: 1.3.6.1.4.1.161.19.3.2.1.133

Syntax: INTEGER
Constraints:

0: instant

1: delayed

2: apply

Access: read-write
Status: current

Used to determine when frequency, cyclic prefix and bandwidth settings take effect for
band scanning MIMO SMs.
0 - Instant
1 - Delayed
2 - Apply changes

radioDbm

Object ID: 1.3.6.1.4.1.161.19.3.2.2.8

Syntax: OCTET STRING
Constraints: SIZE (0..255)
Access: read-only
Status: current

Rx Power level.
For MIMO this is the combined power of the horizontal and vertical paths.

radioDbmAvg

Object ID: 1.3.6.1.4.1.161.19.3.2.2.61

Syntax: INTEGER
Access: read-only
Status: current

Average Receive Power of the AP's beacon in dBm.
OFDM Radios only.
For MIMO this is only the verical path, as the beacon is not transmitted on horizontal.

radioDbmHorizontal

Object ID: 1.3.6.1.4.1.161.19.3.2.2.117

Syntax: OCTET STRING
Constraints: SIZE (0..255)
Access: read-only
Status: current

Receive power level of the horizontal antenna in dBm.
MIMO radios only.

radioDbmInt

Object ID: 1.3.6.1.4.1.161.19.3.2.2.21

Syntax: INTEGER
Access: read-only
Status: current

Radio power level(integer).
For MIMO radios this is the combined power of the horiztontal and vertical paths.

radioDbmVertical

Object ID: 1.3.6.1.4.1.161.19.3.2.2.118

Syntax: OCTET STRING
Constraints: SIZE (0..255)
Access: read-only
Status: current

Receive power level of the vertical antenna in dBm.
MIMO radios only.

radioModeStatus

Object ID: 1.3.6.1.4.1.161.19.3.2.2.127

Syntax: INTEGER
Constraints:

0: undefined

1: pmp430

2: pmp450Interoperability

Access: read-only
Status: current

The current radio mode that SM is operating in.
PMP 430 SMs only.
Introduced in release 12.2.

radioSlicingSm

Object ID: 1.3.6.1.4.1.161.19.3.2.2.5

Syntax: INTEGER
Access: read-only
Status: obsolete

This variable is deprecated.

radioTxGainSm

Object ID: 1.3.6.1.4.1.161.19.3.2.2.6

Syntax: INTEGER
Access: read-only
Status: current

Radio transmission gain setting. Applicable to FSK radios only.

radioTxPwr

Object ID: 1.3.6.1.4.1.161.19.3.2.2.23

Syntax: OCTET STRING
Constraints: SIZE (0..255)
Access: read-only
Status: current

Tx Power level. Valid for FSK and OFDM SMs.

rawBERPwrRxPathA

Object ID: 1.3.6.1.4.1.161.19.3.2.2.125

Syntax: INTEGER
Access: read-only
Status: current

Raw unadjusted BER power level on FPGA Rx Path A of SM.

rawBERPwrRxPathB

Object ID: 1.3.6.1.4.1.161.19.3.2.2.126

Syntax: INTEGER
Access: read-only
Status: current

Raw unadjusted BER power level on FPGA Rx Path B of SM.

realm

Object ID: 1.3.6.1.4.1.161.19.3.2.7.10

Syntax: OCTET STRING
Constraints: SIZE (0..255)
Access: read-write
Status: current

EAP Peer Realm

receiveFragmentsModulationPercentage

Object ID: 1.3.6.1.4.1.161.19.3.2.2.86

Syntax: OCTET STRING
Constraints: SIZE (0..255)
Access: read-only
Status: current

Engineering use only.
The percentage of recent fragments received at which modulation.
For Gen II OFDM only and forward.

registeredToAp

Object ID: 1.3.6.1.4.1.161.19.3.2.2.9

Syntax: OCTET STRING
Constraints: SIZE (0..255)
Access: read-only
Status: current

AP MAC address that the SM registered to.

rfDhcpState

Object ID: 1.3.6.1.4.1.161.19.3.2.1.72

Syntax: INTEGER
Constraints:

0: disabled

1: enabled

Access: read-write
Status: current

To enable or disable RF Interface DHCP feature.

rfScanList

Object ID: 1.3.6.1.4.1.161.19.3.2.1.1

Syntax: OCTET STRING
Constraints: SIZE (0..255)
Access: read-write
Status: current

RF scan list.
The frequencies are:
2.4 radios:24150,24175,24200,24225,24250,24275,24300,24325,24350,24375,
24400,24425,24450,24475,24500,24525,24550,24575.
3.5 radios:340000-360000 added and removed dynamically.
4.9 radios:494500-498500 added and removed dynamically.
5.1 radios:5175,5180,5185,5190,5195,5200,5205,5210,5215,5220,5225,5230,5240,
5245,5250,5255,5260,5265,5270,5275,5280,5285,5290,5295,5300,5305,
5310,5315,5320,5325.
5.2 radios:5275,5280,5285,5290,5295,5300,5305,5310,5315,5320,5325.
5.4 FSK radios:5495,5500,5505,5510,5515,5520,5525,
5530,5535,5540,5545,5550,5555,5560,5565,5570,5575,5580,5585,5590,5595,
5600,5605,5610,5615,5620,5625,5630,5635,5640,5645,5650,5655,5660,5665,
5670,5675,5680,5685,5690,5695,5700,5705.
5.4 OFDM radios 5 mhz channels: 547250,547500,547750,548000,548500,548750,549000,549250,549500,549750,550000,550250,550500,550750,551000,551250,551500,551750,552000,552250,552500,552750,
553000,553250,553500,553750,554000,554250,554500,554750,555000,555250,555500,555750,556000,556250,556500,556750,557000,557250,557500,557750,558000,558250,558500,558750,559000,559250,559500,559750,
560000,560250,560500,560750,561000,561250,561500,561750,562000,562250,562500,562750,563000,563250,563500,563750,564000,564250,564500,564750,565000,565250,565500,565750,566000,566250,566500,566750,
567000,567250,567500,567750,568000,568250,568500,568750,569000,569250,569500,569750,570000,570250,570500,570750,571000,571250,571500,571750.
5.4 OFDM radios 10 mhz channels: 547500,548500,549000,549500,550000,550500,551000,551500,552000,552500,
553000,553500,554000,554500,555000,555500,556000,556500,557000,557500,558000,558500,559000,559500,
560000,560500,561000,561500,562000,562500,563000,563500,564000,564500,565000,565500,566000,566500,
567000,567500,568000,568500,569000,569500,570000,570500,571000,571500.
5.4 OFDM radios 20 mhz channels: 547500,548500,549000,549500,550000,550500,551000,551500,552000,552500,
553000,553500,554000,554500,555000,555500,556000,556500,557000,557500,558000,558500,559000,559500,
560000,560500,561000,561500,562000,562500,563000,563500,564000,564500,565000,565500,566000,566500,
567000,567500,568000,568500,569000,569500,570000,570500,571000,571500.
5.7 FSK radios with ISM enabled :5735,5740,5745,5750,5755,5760,5765,5770,5775,
5780,5785,5790,5795,5800,5805,5810,5815,5820,5825,5830,5835,5840.
5.7 OFDM radios 5 mhz channels :572750,573000,573250,573500,573750,574000,574250,574500,574750,575000,575250,575500,575750,576000,576250,576500,576750,577000,577250,577500,577750,
578000,578250,578500,578750,579000,579250,579500,579750,580000,580250,580500,580750,581000,581250,581500,581750,582000,582250,582500,582750,583000,583250,583500,583750,584000,
584250,584500,584750,585000,585250,585500,585750,586000,586250,586500,586750,587000,587250.
5.7 OFDM radios 10 mhz channels:573000,573500,574000,574500,575000,575500,576000,576500,577000,577500,
578000,578500,579000,579500,580000,580500,581000,581500,582000,582500,583000,583500,584000,584500,585000,585500,586000,586500,587000.
5.7 OFDM radios 20 mhz channels :573500,574000,574500,575000,575500,576000,576500,577000,577500,
578000,578500,579000,579500,580000,580500,581000,581500,582000,582500,583000,583500,584000,584500,585000,585500,586000,586500.
5.8 radios:5860,5865,5870,5875,5880,5885,5890,5895,5900,5905,5910.
5805,5810,5815,5820,5825,5830,5835,5840,5845,5850,5855,5860,5865,5870,5875,5880,
5885,5890,5895,5900,5905,5910,5915,5920,5925,5930,5935,5940,5945,5950.
5.9 radios:5735,5740,5745,5750,5755,5760,5765,5770,5775,5780,5785,5790,5795,5800,
5805,5810,5815,5820,5825,5830,5835,5840,5845,5850,5855,5860,5865,5870,5875,5880,
5885,5890,5895,5900,5905,5910,5915,5920,5925,5930,5935,5940,5945,5950.
6.050 radios:5850,5855,5860,5865,5870,5875,5880,5885,5890,5895,5900,5905,5910,5915,5920,
5925,5930,5935,5940,5945,5950,5955,5960,5965,5970,5975,5980,5985,5990,5995,6000,
6005,6010,6015,6020,6025,6030,6035,6040,6045,6050.
900 radios:9060,9070,9080,9090,9100,9110,9120,9130,9140,9150,9160,9170,9180,9190,9200,9220,9230,9240.
0: none.
all: All frequencies in the band(s) supported by the radio will be selected.
all54: All frequencies in the 5.4 band will be selected (only available on dual band radios).
all57: All frequencies in the 5.7 band will be selected (only available on dual band radios).
When doing a set, separate values with comma with no white space between values.

rfScanListBandFilter

Object ID: 1.3.6.1.4.1.161.19.3.2.1.127

Syntax: INTEGER
Constraints:

8: band5400

9: band5700

Access: read-write
Status: obsolete

This element is obsolete.

rfStatTxSuppressionCount

Object ID: 1.3.6.1.4.1.161.19.3.2.2.96

Syntax: Counter
Constraints: 0..4294967295
Access: read-only
Status: current

RF Scheduler Stats DFS TX Suppression Count

rssi

Object ID: 1.3.6.1.4.1.161.19.3.2.2.2

Syntax: INTEGER
Access: read-only
Status: current

Radio signal strength index. FSK only.

secondaryBER

Object ID: 1.3.6.1.4.1.161.19.3.2.2.30

Syntax: INTEGER
Access: read-only
Status: obsolete

Obsoleted, invalid type to represent this data. Measured Secondary Bit Error Rate.

secondaryBERDisplay

Object ID: 1.3.6.1.4.1.161.19.3.2.2.56

Syntax: OCTET STRING
Constraints: SIZE (0..255)
Access: read-only
Status: current

Measured Secondary Bit Error Rate.
FSK platforms only.

sessionStatus

Object ID: 1.3.6.1.4.1.161.19.3.2.2.1

Syntax: OCTET STRING
Constraints: SIZE (0..255)
Access: read-only
Status: current

SM registered or not.

signalStrengthRatio

Object ID: 1.3.6.1.4.1.161.19.3.2.2.108

Syntax: OCTET STRING
Constraints: SIZE (0..255)
Access: read-only
Status: current

Signal Strength Ratio in dB is the power received by the vertical antenna input (dB) -
power received by the horizontal antenna input (dB).
MIMO radios only.

signalToNoiseRatioSMHorizontal

Object ID: 1.3.6.1.4.1.161.19.3.2.2.106

Syntax: INTEGER
Access: read-only
Status: current

An estimated signal to noise ratio based on the last received data for horizontal antenna.
MIMO radios only.
Will return zero if Signal to Noise Ratio Calculation is disabled.
When operating in MIMO-A will return 0.

signalToNoiseRatioSMVertical

Object ID: 1.3.6.1.4.1.161.19.3.2.2.95

Syntax: INTEGER
Access: read-only
Status: current

An estimated signal to noise ratio based on the last received data.
For GenII OFDM only and forward.
For MIMO this is the vertical antenna.
Will return zero if Signal to Noise Ratio Calculation is disabled.

smAntennaType

Object ID: 1.3.6.1.4.1.161.19.3.2.1.93

Syntax: INTEGER
Constraints:

0: integrated

1: external

Access: read-write
Status: obsolete

Deprecated. See whispBoxStatus.antType for antenna type information.

smLEDModeFlag

Object ID: 1.3.6.1.4.1.161.19.3.2.1.75

Syntax: INTEGER
Constraints:

0: legacy

1: revised

Access: read-write
Status: current

To set LED Panel Operation to Revised Mode(1) or to Legacy Mode(0)

smRateAdapt

Object ID: 1.3.6.1.4.1.161.19.3.2.1.61

Syntax: INTEGER
Constraints:

0: onex

1: onextwox

2: onextwoxthreex

Access: read-write
Status: obsolete

Rate adaptation parameter. 0: no rate adaptation. 1: 1x and 2x adaptation. 2: 1x,2x and 3x adaptation.

smSessionTimer

Object ID: 1.3.6.1.4.1.161.19.3.2.2.36

Syntax: INTEGER
Constraints: 0..4294967295
Access: read-only
Status: current

SM current session timer.

smbFilter

Object ID: 1.3.6.1.4.1.161.19.3.2.1.34

Syntax: INTEGER
Constraints:

0: filterOff

1: filterOn

Access: read-write
Status: obsolete

To set SMB packet filter when NAT is disabled.
Obsolete - Use corresponding OID in whipsBoxConfig MIB.

snmpBerLevel

Object ID: 1.3.6.1.4.1.161.19.3.2.2.25

Syntax: INTEGER
Constraints:

2: twoLevelOrMimoQPSK

4: fourLevelOrMimo16QAM

6: mimo64QAM

8: mimo256QAM

Access: read-only
Status: current

BER level.
For PMP 450 systems: 2=MIMO QPSK, 4=MIMO 16-QAM, 6=MIMO64-QAM, 8=256-QAM
For non PMP 450: 2=2 level BER, 4=4 level BER.

snmpFilter

Object ID: 1.3.6.1.4.1.161.19.3.2.1.35

Syntax: INTEGER
Constraints:

0: filterOff

1: filterOn

Access: read-write
Status: obsolete

To set SNMP packet filter when NAT is disabled.
Obsolete - Use corresponding OID in whipsBoxConfig MIB.

spectrumAnalysisAction

Object ID: 1.3.6.1.4.1.161.19.3.2.1.90

Syntax: INTEGER
Constraints:

0: stopSpectrumAnalysis

1: startTimedSpectrumAnalysis

2: startContinuousSpectrumAnalysis

3: idleNoSpectrumAnalysis

4: idleCompleteSpectrumAnalysis

5: inProgressTimedSpectrumAnalysis

6: inProgressContinuousSpectrumAnalysis

Access: read-write
Status: deprecated

As of release 13.0.2, this OID has been deprecated. Please use the OID in whispBoxConfig.
Start or stop timed or continuous Spectrum Analysis and also give status.
(0) - Stop Spectrum Analysis
(1) - Start Timed Spectrum Analysis
(2) - Start Continuous Spectrum Analysis
(3) - Idle, no Spectrum Analysis results.
(4) - Idle, Spectrum Analysis results available.
(5) - Timed or Remote Spectrum Analysis in progress.
(6) - Continuous Spectrum Analysis in progress.

Note: Continuous mode has a max of 24 hours.

spectrumAnalysisDisplay

Object ID: 1.3.6.1.4.1.161.19.3.2.1.117

Syntax: INTEGER
Constraints:

0: averaging

1: instantaneous

Access: read-write
Status: current

The display for Spectrum Analyzer:
(0) - Averaging over entire period
(1) - Instantaneous showing the last reading

spectrumAnalysisOnBoot

Object ID: 1.3.6.1.4.1.161.19.3.2.1.89

Syntax: INTEGER
Constraints:

0: disable

1: enable

Access: read-write
Status: current

To enable or disable Spectrum Analysis on boot up for one scan through the band.
(0) - Disabled
(1) - Enabled

spectrumAnalysisScanBandwidth

Object ID: 1.3.6.1.4.1.161.19.3.2.1.142

Syntax: INTEGER
Constraints:

0: bandwidth5MHz

1: bandwidth10MHz

2: bandwidth20MHz

Access: read-write
Status: current

Scanning Bandwidth used for the Spectrum Analyzer. Only available on PMP 450.

switchRadioModeAndReboot

Object ID: 1.3.6.1.4.1.161.19.3.2.1.146

Syntax: INTEGER
Constraints:

0: finishedReboot

1: switchRadioModeAndReboot

Access: read-write
Status: current

Setting this to 1 will force switch the SM to the other radio mode and immediately reboot the unit.
When the unit finishes rebooting, it will be in finishedReboot state.
Only will be allowed to be set if both registration options are configured.
PMP 430 SM only.
Introduced in release 12.2.

syslogMinLevelApPreferred

Object ID: 1.3.6.1.4.1.161.19.3.2.1.120

Syntax: INTEGER
Constraints:

0: use-local

1: use-AP-preferred

Access: read-write
Status: current

Uses Syslog minimum transmit level configuration from AP/BHM if available,
otherwise uses local configuration.

syslogSMXmitControl

Object ID: 1.3.6.1.4.1.161.19.3.2.1.121

Syntax: INTEGER
Constraints:

0: obtain-from-AP-default-disabled

1: obtain-from-AP-default-enabled

2: disable

3: enable

Access: read-write
Status: current

Obtains Syslog transmit configuration from AP/BHM if available, or specifies the local transmit state.

syslogSMXmitSetting

Object ID: 1.3.6.1.4.1.161.19.3.2.1.118

Syntax: INTEGER
Constraints:

0: obtain-from-AP

1: enable

2: disable

Access: read-write
Status: deprecated

Obtains Syslog transmit configuration from AP/BHM if set to 0, overrides if 1 or 2. Transmits syslog data to Syslog server if enabled(1), stops if disabled (2).

syslogServerApPreferred

Object ID: 1.3.6.1.4.1.161.19.3.2.1.119

Syntax: INTEGER
Constraints:

0: use-local

1: use-AP-preferred

Access: read-write
Status: current

Uses Syslog server configuration from AP/BHM if enabled and available,
otherwise uses local configuration.

tableIndex

Object ID: 1.3.6.1.4.1.161.19.3.2.5.1.1

Syntax: INTEGER
Constraints: 1..2147483647
Access: read-only
Status: current

User information table index.

tcpGarbageCollectTmout

Object ID: 1.3.6.1.4.1.161.19.3.2.1.21

Syntax: INTEGER
Access: read-write
Status: current

Units of minutes for TCP garbage collection. For multipoint only.
Range 4-1440.

testSMBER

Object ID: 1.3.6.1.4.1.161.19.3.2.1.137

Syntax: INTEGER
Constraints:

0: disable

1: enable

Access: read-write
Status: current

0 - Disable (Return the SM to a normal operation state).
1 - Enable (Set SM into a BER test state).

timedSpectrumAnalysisDuration

Object ID: 1.3.6.1.4.1.161.19.3.2.1.88

Syntax: INTEGER
Constraints: 10..1000
Access: read-write
Status: deprecated

As of release 13.0.2 this value is depricated. Please use the OID in whispBoxConfig.
Value in seconds for a timed spectrum analysis. Range is 10-1000 seconds.

timingPulseGated

Object ID: 1.3.6.1.4.1.161.19.3.2.1.10

Syntax: INTEGER
Constraints:

0: disable

1: enable

Access: read-write
Status: current

0 - Disable (Always propagate the frame timing pulse).
1 - Enable (If SM out of sync then dont propagate the frame timing pulse).

totalBER

Object ID: 1.3.6.1.4.1.161.19.3.2.2.31

Syntax: INTEGER
Access: read-only
Status: obsolete

Obsoleted, invalid type to represent this data. Measured Total Bit Error Rate.

totalBERDisplay

Object ID: 1.3.6.1.4.1.161.19.3.2.2.57

Syntax: OCTET STRING
Constraints: SIZE (0..255)
Access: read-only
Status: current

Measured Total Bit Error Rate.
For MIMO this is combined both paths.

udpGarbageCollectTmout

Object ID: 1.3.6.1.4.1.161.19.3.2.1.22

Syntax: INTEGER
Access: read-write
Status: current

Units of minutes for UDP garbage collection. For multipoint only.
Range 1-1440.

upLinkBCastFilter

Object ID: 1.3.6.1.4.1.161.19.3.2.1.40

Syntax: INTEGER
Constraints:

0: filterOff

1: filterOn

Access: read-write
Status: obsolete

This variable is currently obsolete.

upLnkDataRate

Object ID: 1.3.6.1.4.1.161.19.3.2.1.62

Syntax: INTEGER
Access: read-write
Status: current

Sustained uplink bandwidth cap.

upLnkLimit

Object ID: 1.3.6.1.4.1.161.19.3.2.1.63

Syntax: INTEGER
Access: read-write
Status: current

Burst uplink bandwidth cap.

upLnkMaxBurstDataRate

Object ID: 1.3.6.1.4.1.161.19.3.2.1.128

Syntax: INTEGER
Access: read-write
Status: current

Maximum burst uplink rate.

useRealm

Object ID: 1.3.6.1.4.1.161.19.3.2.7.9

Syntax: INTEGER
Constraints:

0: disable

1: enable

Access: read-write
Status: current

Enable or disable the use of realm option.

userDefinedPort1

Object ID: 1.3.6.1.4.1.161.19.3.2.1.43

Syntax: INTEGER
Access: read-write
Status: obsolete

An integer value of number one user defined port. Range:0-65535
Obsolete - Use corresponding OID in whipsBoxConfig MIB.

userDefinedPort2

Object ID: 1.3.6.1.4.1.161.19.3.2.1.46

Syntax: INTEGER
Access: read-write
Status: obsolete

An integer value of number two user defined port. Range:0-65535
Obsolete - Use corresponding OID in whipsBoxConfig MIB.

userDefinedPort3

Object ID: 1.3.6.1.4.1.161.19.3.2.1.49

Syntax: INTEGER
Access: read-write
Status: obsolete

An integer value of number three user defined port. Range:0-65535
Obsolete - Use corresponding OID in whipsBoxConfig MIB.

userP1Filter

Object ID: 1.3.6.1.4.1.161.19.3.2.1.36

Syntax: INTEGER
Constraints:

0: filterOff

1: filterOn

Access: read-write
Status: obsolete

To set user defined port 1 packet filter when
NAT is disabled.
Obsolete - Use corresponding OID in whipsBoxConfig MIB.

userP2Filter

Object ID: 1.3.6.1.4.1.161.19.3.2.1.37

Syntax: INTEGER
Constraints:

0: filterOff

1: filterOn

Access: read-write
Status: obsolete

To set user defined port 2 packet filter when
NAT is disabled.
Obsolete - Use corresponding OID in whipsBoxConfig MIB.

userP3Filter

Object ID: 1.3.6.1.4.1.161.19.3.2.1.38

Syntax: INTEGER
Constraints:

0: filterOff

1: filterOn

Access: read-write
Status: obsolete

To set user defined port 3 packet filter when
NAT is disabled.
Obsolete - Use corresponding OID in whipsBoxConfig MIB.

wanPingReplyEnable

Object ID: 1.3.6.1.4.1.161.19.3.2.1.95

Syntax: INTEGER
Constraints:

0: disable

1: enable

Access: read-write
Status: current

Allow Ping replies from SM WAN interface. Applies to both NAT and PPPoE WAN interfaces.

whispMappingEntry

Object ID: 1.3.6.1.4.1.161.19.3.2.5.1

Syntax: Sequence (Structure)

tableIndex

protocol

port

localIp

Access: not-accessible
Status: current

Mapping table entry.

whispMappingTable

Object ID: 1.3.6.1.4.1.161.19.3.2.5

Syntax: Sequence of Type (Array)

WhispMappingEntry

Access: not-accessible
Status: current

NAT port mapping information table.

whispSmTranslationTable

Object ID: 1.3.6.1.4.1.161.19.3.2.6

Syntax: Sequence of Type (Array)

WhispSmTranslationTableEntry

Access: not-accessible
Status: current

Translation Table.

whispSmTranslationTableEntry

Object ID: 1.3.6.1.4.1.161.19.3.2.6.1

Syntax: Sequence (Structure)

whispTranslationTableIndex

whispTranslationTableMacAddr

whispTranslationTableIpAddr

whispTranslationTableAge

Access: not-accessible
Status: current

Translation Table Entry.

whispTranslationTableAge

Object ID: 1.3.6.1.4.1.161.19.3.2.6.1.4

Syntax: Counter
Constraints: 0..4294967295
Access: read-only
Status: current

Age of the registered entity.

whispTranslationTableIndex

Object ID: 1.3.6.1.4.1.161.19.3.2.6.1.1

Syntax: INTEGER
Constraints: 1..127
Access: read-only
Status: current

Index into translation table.

whispTranslationTableIpAddr

Object ID: 1.3.6.1.4.1.161.19.3.2.6.1.3

Syntax: STRING
Constraints: SIZE (4)
Access: read-only
Status: current

Ip Address of the registered entity.

whispTranslationTableMacAddr

Object ID: 1.3.6.1.4.1.161.19.3.2.6.1.2

Syntax: OCTET STRING
Constraints: SIZE (6)
Access: read-only
Status: current

MAC Address of the registered enity.

zoltarFPGAFreqOffset

Object ID: 1.3.6.1.4.1.161.19.3.2.2.62

Syntax: INTEGER
Access: read-only
Status: current

FPGA peek of 70001088

zoltarSWFreqOffset

Object ID: 1.3.6.1.4.1.161.19.3.2.2.63

Syntax: INTEGER
Access: read-only
Status: current

FPGA peek of 7000108C